780 mm, it even fits through almost any door. Please read these instructions carefully before using the e-Bikelifter for the first time. If you have any fur- ther questions, please contact info@ebikelifter.com. Furthermore, you can find all the information contained in this manual in German / English / French, as well as pictures and videos of the product, at www.e-bikelifter.com.
There is a risk of getting your fingers crushed. Warning! This pictogram draws attention to the risk of personal injury. The e-Bikelifter must not be used for lifting persons. Warning! This pictogram draws attention to the risk of personal injury.
While not in use or storing, always ensure that the sledge is lowered to under 800 mm height. and is free of any items or cargo. The e-Bikelifter is to be serviced at least once a year or according to laws, regulations, dir- ectives, working conditions and experience. The service shall be performed by the man- ufacturer or a skilled technician.
B: No persons or body parts must be put under the tool or load. C: Do not put objects or limbs (feet, hands, fingers etc.) into any opening of the e-Bikelifter D: Do not put your feet or other parts of your body under the wheels!
7 Operating the e-Bikelifter 7.1 Power ON / OFF switch Remember to turn OFF the e-Bikelifter when not in use! Round button is pressed (it sticks out about 2 mm) Green indicator light OFF: Round button is not pressed (it sticks out about 5 mm) No indicator light www.e-bikelifter.com...
You can only activate one foot switch at the time. No obstacles must be on the base plate, when operating the e-Bikelifter. While lowering the load, an override slip clutch will engage, when the load touches the ground or an obstacle.
7.4 Attaching and detaching a bicycle (VAR PR-72000 clamping arm) The by,schulz e-Bikelifter BM-60 VA and the BM-60-S VA come with the PR-72000 clamping arm by VAR. This clamping arm can be swiveled 360°, and is suitable for clamping tubes with diameters from Ø 22 mm up to Ø...
Note: The e-Bikelifter must stand on a hard and leveled surface. No obstacles or objects must be below the base plate of the e-Bikelifter. The e-Bikelifter must stand firmly and must not swing, when stepping on the base plate www.e-bikelifter.com...
The sledge must be lowered to under 800 mm height and be free of any items or cargo. The e-Bikelifter must be turned off. Fasten the e-Bikelifter securely during transport. Thanks to the e-Bikelifter's lead-gel dry batteries, no battery acid can leak. This makes it possible to transport the e-Bikelifter even lying down! www.e-bikelifter.com...
For each groove, two sliding blocks with an M6 thread are included in the scope of delivery. You can find additional sliding blocks in our online stop at www.byschulz.shop www.e-bikelifter.com...
The batteries are charged with the external charger. Connect the charger to the charging port on the backside of the e-Bikelifter and to a 230V / 110V – 50-60 Hz power source. Although the device charges both when switched on and when switched...
Hovmand strongly recommends the following checks to to be carried out on a daily basis and before using the e-Bikelifter. Ensure that the lift is functioning as intended. If in doubt, do not use. The e-Bikelifter must be free of dirt or debris which could affect safe operation Ensure all warning labels are present, without damage and are readable.
Bikelifter as this may have adverse or a damp cloth. effect on the electrical components. Key inspection points Check the proper function of all components before the e-bike lifter is put back into oper- ation after cleaning. www.e-bikelifter.com...
Remove the dirt and wipe with alcohol. the sledge runs? Is there dirt on the sledge wheels? Remove the dirt or replace the wheels. The e-Bikelifter does not Check whether the item being lifted Remove the item. respond is heavier than the lift's capacity...
Page 25
- hereby declare that the machine: Designation: Mobile battery-powered lifter Type identification number: e-Bikelifter Serial number: _______________________ - is manufactured in accordance with the Machinery Directive 2006/42/EC Annex II A. The following directives and standards as well as technical reports have been applied, insofar as they have...
Page 26
- hereby declare that the machine: Designation: Mobile battery-powered lifter Type identification number: e-Bikelifter Serial number: _______________________ - is manufactured in accordance with the Supply of Machinery Safety Regulations 2008. The following directives and standards as well as technical reports have been applied, insofar as they have...