Advertisement
Installing the AP
Service to all Alcatel-Lucent products should be performed by trained
service personnel only.
Using the Ceiling Rail Adapter
The OAW-AP210 Series ships with two ceiling rail adapters for 9/16" and 15/16"
ceiling rails. Additional wall mount adapters and ceiling rail adapters for other
rail styles are available as accessory kits.
Make sure the AP fits securely on the ceiling tile rail when hanging the
!
device from the ceiling, because poor installation could cause it to fall onto
people or equipment.
1. Pull the necessary cables through a prepared hole in the ceiling tile near
where the AP will be placed.
2. Place the adapter against the back of the AP with the adapter at an angle of
approximately 30 degrees to the tabs (see
Figure
7).
3. Twist the adapter clockwise until it snaps into place in the tabs (see
Figure 7 Attaching the Ceiling Rail Adapter
4. If necessary, connect the console cable to the console port on the back of the
AP.
5. Hold the AP next to the ceiling tile rail with the ceiling tile rail mounting slots
at approximately a 30-degree angle to the ceiling tile rail (see
Figure
sure that any cable slack is above the ceiling tile.
6. Pushing toward the ceiling tile, rotate the AP clockwise until the device clicks
into place on the ceiling tile rail.
Figure 8 Mounting the AP
7. On the OAW-AP214, install the external antennas according to the
manufacturer's instructions, and connect the antennas to the antenna
interfaces on the AP.
Connecting Required Cables
Install cables in accordance with all applicable local and national regulations and
practices.
Verifying Post-Installation Connectivity
The integrated LEDs on the AP can be used to verify that the AP is receiving
power and initializing successfully (see
Table
1). Refer to the AOS-W Quick Start
Guide for further details on verifying post-installation network connectivity.
Configuring the OAW-AP210 Series
AP Provisioning/Reprovisioning
Provisioning parameters are unique to each AP. These local AP parameters are
initially configured on the switch which are then pushed out to the AP and stored
on the AP itself. Alcatel recommends that provisioning settings be configured via
the AOS-W Web UI only. Refer to the AOS-W User Guide for complete details.
AP Configuration
Configuration parameters are network or switch specific and are configured and
stored on the switch. Network configuration settings are pushed out to the AP(s)
but remain stored on the switch.
Configuration settings can be configured via the AOS-W Web UI or AOS-W CLI.
Refer to their respective guides for further details: the AOS-W User Guide.
Product Specifications
Electrical
Ethernet:
1x 10/100/1000 auto-sensing Ethernet RJ-45 Interface
MDI/MDX
IEEE 802.3 (10Base-T), IEEE 802.3u (100Base-T). IEEE 802.3ab (1000Base-T)
Power over Ethernet (IEEE 802.3at and 802.3af compliant), 48V DC (nominal) and 56V DC
(maximum)/350mA (see
Figure 6
for pin configuration)
Power:
Figure
7).
12 VDC power interface, supports powering through an AC-to-DC power adapter
POE support on Ethernet ports: 802.3at-compliant and 802.3af-compliant POE sourcing
devices
If a power adapter other than the one provided by Alcatel-Lucent is used in
the US or Canada, it should be cULus (NRTL) Listed, with an output rated
12 VDC, minimum 1.5A, marked "LPS" or "Class 2," and suitable for
plugging into a standard power receptacle in the US and Canada.
For additional specifications on this product, please refer to the data sheet. The data sheet can be
found at http://www.alcatel-lucent.com/enterprise.
Proper Disposal of Alcatel Equipment
For the most current information about Global Environmental Compliance and
Alcatel products, see our website at http://www.alcatel-lucent.com/enterprise.
Waste of Electrical and Electronic Equipment
Alcatel products at end of life are subject to separate collection and treatment
in the EU Member States, Norway, and Switzerland and therefore are marked
with the symbol shown at the left (crossed-out wheelie bin). The treatment
applied at end of life of these products in these countries shall comply with
the applicable national laws of countries implementing Directive 2002/96EC
on Waste of Electrical and Electronic Equipment (WEEE).
European Union RoHS
8). Make
Alcatel products also comply with the EU Restriction of Hazardous
Substances Directive 2011/65/EC (RoHS). EU RoHS restricts the use of
specific hazardous materials in the manufacture of electrical and
electronic equipment. Specifically, restricted materials under the RoHS
Directive are Lead (including Solder used in printed circuit assemblies), Cadmium, Mercury,
Hexavalent Chromium, and Bromine. Some Alcatel products are subject to the exemptions listed in
RoHS Directive Annex 7 (Lead in solder used in printed circuit assemblies). Products and packaging
will be marked with the "RoHS" label shown at the left indicating conformance to this Directive.
China RoHS
Alcatel products also comply with China environmental declaration requirements
and are labeled with the "EFUP 10" label shown at the left.
10
Hazardous Materials Declaration
(Parts)
PCA Boards)
Mechanical Sub-Assemblies)
SJ/T11363-2006
Indicates that the concentration of the hazardous substance in all homogeneous materials in the parts is
below the relevant threshold of the SJ/T11363-2006 standard.
Indicates that the concentration of the hazardous substance of at least one of all homogeneous materials
in the parts is above the relevant threshold of the SJ/T11363-2006 standard.
This table shows where these substances may be found in the supply chain of electronic information
products, as of the date of sale of the enclosed product.
The Environment- Friendly Use Period (EFUP) for all enclosed products and their parts are
per the symbol shown here. The Environment- Friendly Use Period is valid only when the
product is operated under the conditions defined in the product manual.
India RoHS
This product complies with RoHS requirements as prescribed by E-Waste (Management & Handling)
Rules, governed by the Ministry of Environment & Forests, Government of India.
Safety and Regulatory Compliance
Alcatel provides a multi-language document that contains country-specific restrictions and additional
safety and regulatory information for all Alcatel access points. This document can be viewed or
downloaded from the following location:
https://service.esd.alcatel-lucent.com.
Regulatory Model Names
The following regulatory model names apply to the OAW-AP210 Series:
OAW-AP214: APIN0214
OAW-AP215: APIN0215
FCC
This device is electronically labeled. To view the FCC ID:
1. Log into the switch WebUI.
2. Navigate to Maintenance > Switch > About.
RF Radiation Exposure Statement: This equipment complies with FCC
RF radiation exposure limits. This equipment should be installed and
operated with a minimum distance of 7.9 inches (20 cm) between the
!
radiator and your body for 2.4 GHz and 5 GHz operations. This transmitter
must not be co-located or operating in conjunction with any other antenna
or transmitter. When operated in the 5.15 to 5.25 GHz frequency range, this
device is restricted to indoor use to reduce the potential for harmful
interference with co-channel Mobile Satellite Systems.
FCC Class B Part 15
This device complies with Part 15 of the Federal Communications Commission (FCC) Rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause
undesired operation.
Changes or modifications to this unit not expressly approved by the party
!
responsible for compliance could void the user's authority to operate this
equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the manufacturer's instructions, may cause
interference harmful to radio communications.
If this equipment does cause interference, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment to an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio or TV technician for help.
Complies with the Class B limits for radio noise emissions as set out in the interference-causing
equipment standard entitled "Digital Apparatus," ICES-003 of Industry Canada.
Cet apareil numerique de la classe B respecte toutes les exigencies du Reglement sur le materiel
brouilleur du Canada.
Users are advised that high power Radars are allocated as primary users of the bands 5250-5350 MHz
and 5650-5850 MHz and these Radars could cause interference and/or damage to Licensed Exempt
WLAN devices.
EU Regulatory Conformance
This product is CE marked according to the provisions of the R & TTE Directive
(1999/5/EC) - CE(!). Alcatel-Lucent hereby declares that the APIN0114 / APIN0115
device models are in compliance with the essential requirements and other relevant provisions of
Directive 1999/5/EC -CE(!)
The Declaration of Conformity made under Directive 1999/5/EC is available for viewing at
www.alcatel-lucent.com/enterprise.
Canada
(i)les dispositifs fonctionnant dans la bande 5 150-5 250 MHz sont réservés uniquement pour une
utilisation à l'intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de
satellites mobiles utilisant les mêmes canaux;
(ii) le gain maximal d'antenne permis pour les dispositifs utilisant les bandes 5 250-5 350 MHz et 5 470-
5 725 MHz doit se conformer à la limite de p.i.r.e.;
(iii) le gain maximal d'antenne permis (pour les dispositifs utilisant la bande 5 725-5 825 MHz) doit se
conformer à la limite de p.i.r.e. spécifiée pour l'exploitation point à point et non point à point, selon le
cas.
(Hazardous Substance)
De plus, les utilisateurs devraient aussi être avisés que les utilisateurs de radars de haute puissance
sont désignés utilisateurs principaux (c.-à-d., qu'ils ont la priorité) pour les bandes 5 250-5 350 MHz et
5 650-5 850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs
LAN-EL.
Aucune émission n'est permise dans la bande 5 600-5 650 MHz. Jusqu'à
nouvel avis, les dispositifs visés par la présente annexe ne doivent pas être
en mesure d'émettre dans la bande 5 600-5 650 MHz, afin de protéger les
radars météorologiques d'Environnement Canada exploités dans cette
bande.
RF Déclaration sur la radioexposition: Cet équipement est conforme aux
normes IC Limites d'exposition aux rayonnements RF. Cet équipement doit
!
être installé et utilisé à une distance minimum de 7,9 pouces (20 cm) entre
l'radiateur et votre corps pour 2,4 GHz et 5 GHz opérations. cet émetteur ne
doit pas être co-localisées ou opérant en conjonction avec une autre
antenne ou émetteur.
OAW-AP210 Series Wireless
Access Point
Installation Guide
Contacting Alcatel-Lucent
Web Site Support
Main Site
http://www.alcatel-lucent.com/enterprise
Support Site
https://service.esd.alcatel-lucent.com
Support Email
esd.support@alcatel-lucent.com
Telephone Support
North America
1-800-995-2696
Latin America
1-877-919-9526
Europe
+800 00200100 (Toll Free) or
1-650-385-2193
Asia Pacific
+65 6240 8484
Worldwide
1-818-878-4507
Copyright
Copyright © 2014 Alcatel-Lucent. All rights reserved.
Specifications in this manual are subject to change without notice.
Originated in the USA.
Trademarks
http://
AOS-W, Alcatel 4302, Alcatel 4304, Alcatel 4306, Alcatel 4308, Alcatel 4324, Alcatel 4504, Alcatel 4604, Alcatel
4704, Alcatel 4550, Alcatel 4650, Alcatel 4750, Alcatel 6000, OAW-AP41, OAW-AP68, OAW-AP60/61/65,
OAW-AP70, OAW-AP80, OAW-AP92/93, OAW-AP104/105, OAW-AP114/115, OAW-AP120/121, OAW-AP124/
125, OAW-RAP155, OAW-AP175, OAW-IAP92/93, OAW-AP204/205, OAW-AP214,/215, OAW-AP224/225,
OAW-AP274/275, OAW-RAP2, OAW-RAP5, and Omnivista 3600 Air Manager are trademarks of Alcatel-Lucent in
the United States and certain other countries.
Any other trademarks appearing in this manual are the property of their respective companies.
Legal Notice
The use of Alcatel-Lucent switching platforms and software, by all individuals or corporations, to terminate Cisco
or Nortel VPN client devices constitutes complete acceptance of liability by that individual or corporation for this
action and indemnifies, in full, Alcatel-Lucent from any and all legal actions that might be taken against it with
respect to infringement of copyright on behalf of Cisco Systems or Nortel Networks."
www.alcatel-lucent.com
26801 West Agoura Road
Calabasas, CA 91301
OAW-AP210 Series Wireless Access Point | Installation Guide
Part Number 0511571-01 | June 2014
Advertisement
