Advertisement
REPAIR INSTRUCTION
Note:
Please note after replacing the boiler the appliance has to be
restored to factory default. The fi lling procedure (cold fl ush),
known from the predecessor Senseo's is no longer available
after the fl ush before fi rst use has been executed. When the
"restore to factory default" procedure is not carried out, a new
and empty boiler can be switched on, without having the
protection of the initial fl ush procedure, causing the thermal
fuses in the heating element to fail.
After a boiler replacement or drained system, carry
!
out the "Restore boiler_empty_fl ag to factory default"
procedure! Then the initial fl ush procedure can be
carried out.
Descaling
Descaling is an important element in Senseo maintenance.
It should be done at least once every 3 months, up to 6 times
a Year! This will prolong the life of your appliance and will
guarantee optimal brewing results for a long time.
Use the correct descaling agent. Only citric acid-based
descalers are suitable for descaling the SENSEO
This type of descaler descales the appliance without damaging
it. For the correct amount, see under 'Descaling procedure'
below.
Each descaling mixture can be used only once. After use, the
descaling mixture is no longer active. We advise you to use
®
the special SENSEO
Descaler (HD7006).
Read the instructions on the package of the descaling agent.
Never use a descaling agent based on mineral acids such as
sulphuric acid, hydrochloric acid, sulphamic acid and acetic
acid (e.g. vinegar). These descaling agents may damage your
®
SENSEO
coffee machine.
Follow the steps in the section headed "Descale the appliance"
see DFU (Direction for Use manual).
Volume adjustment
The PCB circuit board makes it possible to adjust the volume
output by means of pushing the one-cup and two-cup user
controls.
How to adjust the volume output:
1. Make sure the boiler is fi lled properly, otherwise perform
fi ll procedure see DFU for instructions.
2. Switch appliance on and wait until the unit is ready to
brew.
3. Make sure a pod holder is placed, but without a Coffee
POD. (Only adjusting with plain water)
4. Place a cup on the drip tray cover and push the one-cup
button.
5. When the appliance has fi nished it is stabilized to perform
the volume adjustment.
6. Empty the cup, podholder and push again for one cup
setting, measure the volume output with a graduated
beaker. In the table you can fi nd the requirements for
the minimum / maximum volume output cc/mL values
depending from the country version:
®
machine.
7. Unplug the appliance from the mains.
8. Press the 1- and 2 cup button simultaneously and plug
the mains on.
9. When above step succeeded the LED will turn on
continuously.
10. Depending if the volume has to de- or increase you have
to push the one- or two cup button.
Every time you push the 1- or 2 cup button the LED will
turn off for 0.5 second (feedback to user) and the pump
time will be shortened or lengthened for 0.5 seconds
depending which button was pushed.
Pushing 1 cup button pump, time will be shorten with
0.5 sec is approximately − 3.5 cc/mL (less coffee)
Pushing 2 cup button pump, time will be lengthen with
0.5 sec is approximately + 3.5 cc/mL more coffee)
When the volume has to increase with 10 cc for example,
push the 2 cup button 3 times. The new value will be
stored when you switch the appliance off by pushing the
main switch. (LED will turn off ).
11. Turn appliance on again and brew one cup, measure the
volume. In case the volume is not within specifi cation
repeat steps 6 - 11.
12. End.
HD7825/50 /51 /58
One-cup setting, Including Pod holder, water spec.
(Without Coffee pod)
Min. water cc/mL
Spanish version
51
France version
101
General version
123
Max. water cc/mL
71
121
143
3-8
Advertisement
