1. Manuals
  2. Brands
  3. Electrolux Manuals
  4. Ventilation Hood
  5. ICON E40PV100FS
  6. Installation manual

Electrolux Icon E40PV100FS Installation Manual

Hide thumbs Also See for Icon E40PV100FS:
Table of Contents

Advertisement

Quick Links

Download this manual
Installation
INSTALLATION PLANNING
A qualified installer must complete the installation of this built-in appliance. Proper
installation is your responsibility.
Carefully check the location where the hood is to be installed. The hood should be
placed for convenient access. Make certain that electrical power can be provided
in the selected location.
Plan the installation so that all minimum clearances are met or exceeded.
Dimensions shown provide minimum clearances, unless otherwise noted.
Make certain that you have everything necessary to ensure a proper
installation before proceeding.

Advertisement

Table of Contents
loading

Related Manuals for Electrolux Icon E40PV100FS

Summary of Contents for Electrolux Icon E40PV100FS

  • Page 1 Installation INSTALLATION PLANNING A qualified installer must complete the installation of this built-in appliance. Proper installation is your responsibility. Carefully check the location where the hood is to be installed. The hood should be placed for convenient access. Make certain that electrical power can be provided in the selected location.

  • Page 2: Installation

    Installation VERIFY PACKAGE CONTENTS Unpack hood and check contents. You should receive: 1 - Hood 1 - Decorative Flue Assembly 1 - Support Frame 1 - Duct Collar 1 - Parts Bag containing: 8 - Washers ø 6.4 4 - Washers ø 4.5 4 - Lag Bolts 8 - Mounting Screws (3.9 X 9.5mm Pan Head) 4 - Hex Nuts...

  • Page 3: Installing The Ductwork

    Installation INSTALLING THE DUCTWORK CAUTION To reduce the risk of fire, use only metal ductwork. 1 Decide where the ductwork will run between the hood and the outside. Figure 5. 2 A straight, short duct run will allow the hood to perform most efficiently. 3 Long duct runs, elbows, and transitions will reduce the performance of the hood.

  • Page 4: Installing The Support System

    Installation INSTALLING THE SUPPORT SYSTEM 1 At hood location, install 2 x 4 cross framing between ceiling joists TOP VIEW OF SUPPORT FRAME using dimensions shown in Figure 6. 2 Finish the ceiling surface. Be sure to mark the location of the 9-13/16”...

  • Page 5: Connecting The Decorative Flue

    Installation CONNECTING THE DECORATIVE FLUE 1 Secure the upper flue to the upper support frame with the mounting screws (3.9 x 9.5mm). 2 Insert the lower flue moving it completely towards the top and secure it temporarily with retaining screws (3.9 x 9.5mm). MOUNTING SCREWS INSERT THE LOWER FLUE...

  • Page 6: Mounting The Hood To Support Frame

    Installation MOUNTING THE HOOD TO SUPPORT FRAME 1 Insert four (4) bolts through the top of the hood from the inside. 2 Use four (4) nuts and four (4) washers to secure hood to support frame. WASHER BOLT Figure 12 INSTALLING THE ELECTRICAL WARNING Electrical wiring must be done by a qualified person(s) in accordance with all applicable...

  • Page 7: Connecting The Ductwork

    Installation CONNECTING THE DUCTWORK 1 Use 8” round metal duct to connect the discharge collar on the hood to the ductwork above. LOWER FLUE 2 Use duct tape to make all joints secure and air tight. RETAINING 3 Remove the two temporary retaining screws from the lower flue and set SCREWS it in place on the hood.

  • Page 8: Installing The Filter(S)

    INSTALLING THE FILTER(S) 1 To remove the grease filter, grip the latch and pull it down. This will disengage the filters from the hood. Tilt the filter downward and remove. 2 To install the grease filter, align rear filter tabs with slots in the hood. Pull latch tab down, push filter up into position and release the tab.

Table of Contents