Electrolux E30WV60EPS Installation Instructions Manual
Hide thumbs
Also See for E30WV60EPS:
- Brochure & specs (2 pages) ,
- Wiring diagram (1 page) ,
- Design manual (164 pages)
Advertisement
Quick Links
Advertisement
Related Manuals for Electrolux E30WV60EPS
Summary of Contents for Electrolux E30WV60EPS
- Page 1 ]nsta]]atian Instructions Vc_t l/ood...
- Page 2 BEADAND SAVET SE IINS U DONS Read all instructions before installing the hood. For your safety, please read and observe all safety instructions. Thb guide will help you antbipate all installation connections. For toll-free telephone support in the U.S. and Canada: 1-877- 4ELEOTROLUX (1-877-435-3287) For online support and lnternet...
- Page 3 TABLE OF'CONTENT9 Finding Information ........... 2 PleaseReadAnd SaveThis Guide ....2 Questions ............2 TableOf Contents ..........3 Safety ..............Important S afetyInstructions ......4 Preparing for installation ........7 Verifying Package Contents....... 7 Installation Planning ........... 7 Specifications andDimensions ......8 Exhaust Duct Locations........
- Page 4 £NT S£FEW IINS U Safety Precautions Do not attempt to install or operate your unit until you have read the safety precautions in this manual. Safety items throughout this manual are labeled with a Warning or Caution based on the risk type. ,5!:,, T his is the safety alert symbol.
- Page 5 SAFETY PRECAUTIONS...
- Page 7 VEB F'¥PACKAGE CONTENTS Use and Care Manual Suction II N A qualified installer must complete the installation of this builtqn appliance. Proper installation is your responsibility. Carefully check the location where the hood is to be installed. The hood should be placed for convenient access.
- Page 8 9" Hood Overall Dimensions Model Width "A" Width "B" E30WV60EPS 29 7/8" (759mm) 2313/16" (605ram) E36WV60EPS 357/8" (911mm) 2313116"(605ram) E48WV12EPS 47 7/8" (1216ram) 2313/16" (605ram) Overall Dimensions Isometric View (9" hood shown) Figure 1 18" Hood Overall Dimensions Width "A"...
- Page 9 Verticam Exhaust Duct Location E3OWV6OEPS, E36WV60EPS, E308WV6OES, E368WV60ES Top View Figure 3 6 1/8" (156mm) 8" (203ram) Round Duct Collars Horizontal Exhaust Duct Location Vertical Exhaust Duct Location E308WV60ES, E368WV60ES E48WV12EPS Rear View Top View Figure 5 Figure 6 Horizontal Exhaust Duct Location 5304449697...
- Page 10 EL,,EC CAL,CONDUT IIIL,,,,,,,OCAT ONS 1 1/2" 1/2" 7/8"_ (11Pqm) Holes (_8 _!_)m_rl Conduit Location Conduit Location E3OWV6OEPS, E36WV60EPS, E48WV12EPS, E308WV6OES, E368WV60ES, E488WV120S E3OSWV6OES, E368WV60ES, E488WVI20S ReadBack View Top View 18" Hoods 9" and 18" Hoods Figure 9 Figure 10 Electrical Conduit Locations Model No.
- Page 12 Refer to the table beUow for recommended maximum straight Rengths of duct to provide adequate performance. Model Duct Maximum Equivalent Straight Lengths Size E3OWV6OEPS 10" E36WV60EPS 31/4"x10" E48WV12EPS E3OSWV6OES E368WV60ES E488WV120S E3OWV6OEPS E36WV60EPS E3OSWV6OES E368WV60ES Refer to the table beUow for recommended sheet metaU eUbows, transitions, wall cap equivaUent straight Rengths.
- Page 13 IP PABINGTHE C£B N Minimum hood clearances are zero inches (0") to the rear, sides and top of the hood. Thirty inches (30") is the minimum distance between the bottom of the hood and any cooking surface. Maximum effective cUearance from cooking surface to bottom of hood is 36"...
- Page 14 It is the owner's responsibility to ensure that the electrical connection of this appliance is performed by a qualified electrician. The electrical installation including minimum supply wire size and grounding, must be in accordance with the latest revision of the National Electric code ANSI/NFPA and local codes and ordinances.
- Page 15 IINIWAI,,,,,,,,,,I,,,,,,,,,,ING TIE HOOD First temporarily mount a 2x4 ledger board 30" (762mm) from the finished countertop. Then, remove the filters from the hood canopy and remove the shields below the power ventilator. Secure the hood through the keyhole slots in the top of the hood and/or the slot hole in the rear of the hood.
- Page 16 MAKINGTHE ELEC C£L CONNECTION Electrical power source wiring can be Figure 13 connected through the top or back of the hood. Access the wiring inside the hood canopy in the area to the right side of the power ventilator. Connect the pre=wJred 12"...
- Page 17 :'¥1NG THEOPERATION install the fiRers. Verify that the hood control knobs are in the OFF position. Turn on the main power supply. The hood has two knobs that control the function of the hoods Halogen lights and the exhaust blower. Turning the knobs clockwise will turn on the lights and the blower.