Girl tech KEEPSAFE BOX 2 Instruction Manual

ABOUT KEEPSAFE BOX 2
Keepsafe Box 2 is a high-tech storage
container that opens by remote control. You
can put jewellery, money, notes and other
personal items inside to protect them from
intruders!
The three-button remote control can be
attached to a keychain, backpack or purse.
When you press the correct combination, the
Keepsafe Box 2 will
open!
holes at the back
can be attached to your
wrist or bag.
SETTING UP KEEPSAFE BOX 2
Unscrew the battery compartment on the box
and insert three (3) AA batteries into the unit.
Replace the cover.
SETTING YOUR CODE
1) To open Keepsafe Box 2, press the
WAKE UP button on the lid of the box
once. The yellow light will flash to let you
know the unit is awake.
2) The Keepsafe Box 2 comes with a preset
code which opens the box (default code).
On the remote control press the EYE
button, then the SWIRL and then the
FLOWER. The lights will flash and the lid
will pop up.
NOTE: If the unit will not open, remove and
then re-insert the batteries (see "Replacing
the Batteries"). This will reset the computer
to the default code: Eye, Swirl, Flower. Next,
repeat Step 1.
3) Inside the box is a SET button. Hold the
SET button down for three seconds. The
yellow light next to the THUMB PRINT ID
button will turn on.
4) Create your own three-button code and
enter it on the remote control. You can
use any combination, and any of the three
buttons can be used more than once. For
Inside, a small
example, your new code could be Flower,
locket can hold
Swirl, Flower, or maybe Eye, Swirl, Swirl.
a photo of your
best friend or
As you enter your new code, the green lights
favourite pop
which correspond to the buttons you are
star, which, by
pressing will turn on. After you have entered
using the two
all three buttons, there will be a three-second
pause, and then you will see the green lights
flash in the order of the code you entered.
This means that your code was entered
successfully.
You can change your code anytime by
pressing the SET button and holding it down
for three seconds.
FORGOTTEN YOUR CODE?
If you forget your code, remove and re-insert
the batteries to make the unit return to the
default code: Eye, Swirl, Flower. Open the
unit again with this code and enter a new
three-button code.
OPENING KEEPSAFE BOX 2
WITH YOUR NEW CODE
Close the lid on the Keepsafe Box 2. If the
yellow light is not flashing, press the WAKE
UP button to ready the unit. Now enter your
three-button code. Each time you press a
button, you will have 10 seconds to press the
next button. If you wait more than 10 seconds,
the computer inside Keepsafe Box 2 will
detect an error and you must start again.
PLAY MODE
On the side of the Keepsafe Box 2, there's a switch
which can be set for either "Long Play" or "Short Play".
Short Play mode saves batteries, but the
Keepsafe Box 2 will go into sleep mode after
one minute of non-play. In Long Play mode,
the unit goes into sleep mode after 30
minutes of non-play. You can tell the unit is
awake when the yellow light is flashing.
SECRET COMPARTMENTS
There are three secret compartments inside
Keepsafe Box 2, two can be found inside the
box lid, both are big enough to hold your best
secret stuff! Press on the tabs to open each
compartment.
The other compartment can be found in the
top-left corner, inside the box. Slide the
drawer to the left, and below you will find
more secret storage!
PHOTO LOCKET
When you open the lid you will see the
special photo locket. To open it and change
the photo, twist the back and pull apart. The
window can now be pushed out and a photo
of your choice placed behind it. By threading
a cord through the two holes at the back the
locket can be attached to your wrist or bag.
BATTERY LIFE INDICATOR
Next to the THUMB PRINT ID button is a
small, red LED light. This light will turn on
when the battery is getting low. If you see this
light turn on, replace the batteries as soon as
possible.
TO MANUALLY OPEN THE LID:
• Remove the outermost battery.
• Insert a small screwdriver into the
rectangular opening at the breakaway tab