Related Manuals for Ahrend SilenceCHAT
Summary of Contents for Ahrend SilenceCHAT
- Page 1 Silence CHAT This Manual will help you build the perfect solution for a comfortable conversation. Page 1 december 24, 2020...
- Page 2 Page 2 december 24, 2020...
- Page 3 Floor Make sure the floor is perfectly level. Level / Allen 4 Page 3 december 24, 2020...
- Page 4 Corner Posts They fit on every corner. Do not tighten the bolts yet. M10 x 25 / Allen 8 Page 4 december 24, 2020...
- Page 5 Top Bars Make sure the bolts are in place before letting go. Do not tighten the bolts yet. M10 x 25 / M10 Washer / M10 Nut / Allen 8 / Wrench 17 Page 5 december 24, 2020...
- Page 6 Walls Make sure the bolts are in place before letting go. Now tighten all bolts on corner posts and top bar members. M5 x 25 / Allen 3 Page 6 december 24, 2020...
- Page 7 Glass Profiles Make sure the flange is on the inside. M5 x 25 / Allen 3 / M5 x 10 / Phillips screwdriver Page 7 december 24, 2020...
- Page 8 Velt Velt defines the table. Meeting table Working table Meeting table low (75 cm) Working table low (75 cm) Door Door side side Meeting table high (110 cm) Working table high (110 cm) Door Door side side Page 8 december 24, 2020...
- Page 9 Frame Meeting Table Make sure open profile is positioned towards the glass. Page 9 december 24, 2020...
- Page 10 Meeting Table Make sure to place bolts before moving on. M5 x 12 / Allen 4 Page 10 december 24, 2020...
- Page 11 Frame Working Table Place the frames from the outside of the wall and push them inwards. M8 x 16 / Allen 6 Page 11 december 24, 2020...
-
Page 12: Working Table
Working Table Make sure to place bolts before moving on. M5 x 12 / Allen 4 Page 12 december 24, 2020... - Page 13 Place Cables Place and connect cables from Control Unit and pull them through Frametube and out the wall. Page 13 december 24, 2020...
-
Page 14: Control Unit
Control Unit Be careful not to damage wires. M6 x 16 / Allen 5 / M6 Washer / M6 Nut Page 14 december 24, 2020... - Page 15 Monitor Support (Optional) Be careful not to damage wires. M6 x 20 / Allen 5 / M6 Washer / M6 Nut M5 x 12 / Allen 4 Page 15 december 24, 2020...
-
Page 16: Glass Panels
Glass Panels Make sure not to leave the glass unattended for, until all profiles and rubbers are installed. Plastic Glass Strip / Plastic Fillers (bottom) Page 16 december 24, 2020... - Page 17 Glass Panels Make sure not to leave the glass unattended for, A = A until all profiles and rubbers are installed. B = B Use EQUAL amount of fillers on each side and Plastic Fillers (sides) place enough to make them FIXED Page 17 december 24, 2020...
- Page 18 Glass Profiles Make sure not to leave the glass unattended for, until all profiles and rubbers are installed. Thick Rubber Profile / Glass Cleaner Page 18 december 24, 2020...
-
Page 19: Door Assembly
Door Assembly Make sure too make a perfect corner. Allen 2.5 / Small Bracket / Large Bracket Page 19 december 24, 2020... - Page 20 Place Door Frame Place carefully and make sure corners of the door are perfectly assembled. Make sure flange is on the inside. M5 x 25 / Allen 3 Page 20 december 24, 2020...
- Page 21 Glass Panels Make sure not to leave the glass unattended for, until all profiles and rubbers are installed. Rubber Tape / Plastic Fillers (bottom) Page 21 december 24, 2020...
- Page 22 Glass Profiles Make sure not to leave the glass unattended for, until all profiles and rubbers are installed... Thick & Thin Rubber Profile / Glass Cleaner Page 22 december 24, 2020...
- Page 23 Place Hygienic Filters Place from inside. Page 23 december 24, 2020...
- Page 24 Velt Panels Place from inside. Page 24 december 24, 2020...
- Page 25 PET Ceiling Lift over top bars and place from the top. M5 x 12 / Allen 4 Page 25 december 24, 2020...
- Page 26 Electric wire diagram - type LUXE / Ready FO / Basic Install table + felt + electric BEFORE the glass wall Place FAN PLUG on right spot. BEFORE the wooden ceiling. Use clip, to put cable in place...
- Page 27 Electric wire diagram - type LUXE / Ready FO / Basic Install table + felt + electric BEFORE the glass wall Place FAN PLUG on right spot. BEFORE the wooden ceiling. Use clip, to put cable in place...
- Page 28 Electric wire diagram - type LUXE / Ready FO / Basic Install table + felt + electric BEFORE the glass wall Place FAN PLUG on right spot. BEFORE the wooden ceiling. Use clip, to put cable in place...
- Page 29 Acoustic Filling Place properly against edges of ceiling Page 27 december 24, 2020...
-
Page 30: Top Panel
Top Panel Place from top. M10 x 25 / M10 Washer / Allen 8 M5 x 25 / M5 Washer / Allen 4 Page 28 december 24, 2020... - Page 31 Adjust Ceiling Use screw to pull the ceiling upwards and make the bottom of the ceiling level. M5 x 90 / M5 Washer / Allen 4 Page 29 december 24, 2020...
-
Page 32: Fan Housing
Fan Housing Make sure to plug in all connectors. Page 30 december 24, 2020... - Page 33 Place Door Make sure door is vertical and closes in the corners. If the corners don't close Place hinges outwards. Top 2 Bottom 1 Allen 4 / Allen 3 Page 31 december 24, 2020...
- Page 34 Place Carpet Make sure the carpet is down, so noone trips. 2 Sided Tape Page 32 december 24, 2020...
- Page 35 Fabric Panels Be carefull. Do not drop the Fabric Panels on its corners. Deformation might occur. Page 33 december 24, 2020...
- Page 36 Fabric Panels Adjust the Fabric Panels from the inside, by placing a screw on the inside of the Corner Posts. LIFT VELT M5 x 25 / Allen 3 Page 34 december 24, 2020...
- Page 37 Place Drop Seal Make sure first time is right. Tape does not come of. CENTER Adjust Drop Page 35 december 24, 2020...
- Page 38 Silence CHAT Enjoy! Page 36 december 24, 2020...
Need help?
Do you have a question about the SilenceCHAT and is the answer not in the manual?
Questions and answers