CONTENTS USING THE UNIT SAFELY......................3 PRODUCTS AND ACCESSORIES...................7 Optional Accessories......................8 PRODUCT COMBINATION.......................9 OPERATION AND CONNECTIONS..................12 KOS Satelite Set PANEL FUNCTION INTRODUCTION............18 KOS Sub PANEL FUNCTION INTRODUCTION..............20 SPECIFICATION........................22 SUPPORT AND TROUBLESHOOTING...................23...
Optional Accessories Cable*1 0.6M Signal Cable 2M Signal Cable 0.6M Power Cable 2M Power Cable 3M Power Cable*1 KOS Sub KOS Pole KOS Extension Hanger...
PRODUCT COMBINATION COMBINATION 1 Recommended Configuration Cable*1 KOS Satelite Set*1 KOS Pole Set Adaptor 2M Signal Cable 2M Power Cable Pole 3M Power Cable KOS Sub*1...
Page 10
PRODUCT COMBINATION COMBINATION 2 Recommended Configuration Cable*2 KOS Satelite Set*2 0.6M Signal Cable*3 0.6M Power Cable*3 3M Power Cable KOS Sub*2...
Page 11
PRODUCT COMBINATION COMBINATION 3 Recommended Configuration 0.6M Signal Cable*3 Cable*2 KOS Satelite Set*2 KOS Flybar*1 0.6M Power Cable*3 3M Power Cable KOS Sub*2...
DSP SETUP Combination Mode 1 One KOS Sub is connected to a set of KOS Satelite Set through a pole, and the DSP is set at the 1 position. Use on the floor, suitable for small performances. Connecting and Disassembling Method of Quick Locked Design Installation 1.
Page 13
OPERATION AND CONNECTIONS Power and Signal Cable Wiring Diagrams Supporting Cable KOS Satelite Passive KOS Satelite Active KOS Sub Signal Output Signal Input Power Input...
Page 14
Combination Mode 2 Two KOS Subs are connected to two sets of KOS Satelite Set, and the DSP is set at the 2 position. DSP SETUP Use on the floor, suitable for medium to large performances.
Page 15
OPERATION AND CONNECTIONS Power and Signal Cable Wiring Diagrams Supporting Cable KOS Satelite Passive KOS Satelite Active Supporting Cable KOS Satelite Passive Signal Cable Power Cable KOS Satelite Active Power Cable Signal Cable KOS Sub Signal Cable Power Cable KOS Sub Signal Input Power Input...
Page 16
Two KOS Subs are connected to two sets of > 65ft > KOS Satelite Set, and the DSP is set at the 3 or 4 position.Use by flybar, suitable for medium to large DSP SETUP performances. Connecting and Disassembling Method of Quick Locked Design Installation 1.
Page 17
OPERATION AND CONNECTIONS Power Input Signal Input KOS Sub Power Cable Signal Cable KOS Sub Signal Cable Power Cable KOS Satelite Passive Power Cable Signal KOS Satelite Active Cable Supporting Cable KOS Satelite Passive Supporting Cable KOS Satelite Active...
KOS Satelite Set PANEL FUNCTION INTRODUCTION CONTROL PANEL EQU setup CONNECT TO KOS Satelite Active STAND KOS Satelite Passive EQU setup STACK EQU setup FLOWN NEAR > 20m NO intermal 65ft 65ft passive filter MADE IN CHINA SENSITIVITY CONNECT TO KOS Satelite Passive...
Page 19
When there is an input it will be silent or damage product. signal, the light will be green. When the machine reaches 2. This port is limited to using the KOS Satelite Set’s amplifier full power, the light will be red. signal output.
KOS Sub PANEL FUNCTION INTRODUCTION CONTROL PANEL -6dB POWER -3dB 90Hz 120Hz SIG/LIMIT +3dB SENSITIVITY X-OVER X-OVER LINK MAINS LINK SUB PHASE OUTPUT MODE PUSH MADE IN CHINA MAINS INPUT LINE IN LINK OUT...
Page 21
2. Volume Control There are a total of 4 levels of input sensitivity adjustment, which only control the sensitivity of this product and supporting KOS Satelite Set. This does not affect the signal strength of LINKOUT (8). 3. Power When the machine is powered on, the indicator light is blue, indicating that the power supply of the machine is normal.
SPECIFICATION KOS Satelite Set KOS Sub Inputs Output Power output Volume Power input Class D + switching power design Class D + switching power design Switching power design LED power / signal / clip indicator Features LED power / signal / clip indicator...
SUPPORT AND TROUBLESHOOTING TROUBLESHOOTING A Make sure the power cable connection is plugged in tightly and turn right to the ON position. B Make sure all cables and other connected devices are properly and securely connected. No sound from C Make sure the DSP and LEVEL setting gears are in the position corresponding to the normal gears. the loudspeaker D Make sure the sound source device is functioning properly and can play the desired signal.