Table of Contents
Advertisement
The power steering fluid level should be checked
regularly. To check the power steering fluid
level, be sure the engine is "OFF", then check
to make certain that the power steering fluid
level is between the "MAX" and "MIN" level
markings on the fluid reservoir.
NOTE:
NOTE:
NOTE:
NOTE:
NOTE:
Grinding noise from the power steering
Grinding noise from the power steering
Grinding noise from the power steering
Grinding noise from the power steering
Grinding noise from the power steering
pump may be heard immediately after the
pump may be heard immediately after the
pump may be heard immediately after the
pump may be heard immediately after the
pump may be heard immediately after the
engine is started in extremely cold condi-
engine is started in extremely cold condi-
engine is started in extremely cold condi-
engine is started in extremely cold condi-
engine is started in extremely cold condi-
tions (below - 4°F). In this case, if the noise
tions (below - 4°F). In this case, if the noise
tions (below - 4°F). In this case, if the noise
tions (below - 4°F). In this case, if the noise
tions (below - 4°F). In this case, if the noise
stops during warm up, there is no abnormal
stops during warm up, there is no abnormal
stops during warm up, there is no abnormal
stops during warm up, there is no abnormal
stops during warm up, there is no abnormal
function in the system. This is due to a
function in the system. This is due to a
function in the system. This is due to a
function in the system. This is due to a
function in the system. This is due to a
power steering fluid characteristic in ex-
power steering fluid characteristic in ex-
power steering fluid characteristic in ex-
power steering fluid characteristic in ex-
power steering fluid characteristic in ex-
tremely cold conditions.
tremely cold conditions.
tremely cold conditions.
tremely cold conditions.
tremely cold conditions.
Recommended Fluid
Recommended Fluid
Recommended Fluid
Recommended Fluid
Recommended Fluid
Use PSF-3 type fluid
NOTE:
NOTE:
NOTE:
NOTE:
NOTE:
Do not start the engine when the power
Do not start the engine when the power
Do not start the engine when the power
Do not start the engine when the power
Do not start the engine when the power
steering oil reservoir is empty.
steering oil reservoir is empty.
steering oil reservoir is empty.
steering oil reservoir is empty.
steering oil reservoir is empty.
G240A01A-AAT
POWER STEERING HOSES
POWER STEERING HOSES
POWER STEERING HOSES
POWER STEERING HOSES
POWER STEERING HOSES
It is suggested that you check the power steer-
ing hose connections for fluid leakage at those
intervals specified in the vehicle maintenance
schedule in Section 5.
The power steering hoses should be replaced if
there is severe surface cracking, pulling, scuff-
ing or worn spots. Deterioration of the hose
could cause premature failure.
DO-IT-YOURSELF MAINTENANCE
DO-IT-YOURSELF MAINTENANCE
DO-IT-YOURSELF MAINTENANCE
DO-IT-YOURSELF MAINTENANCE
DO-IT-YOURSELF MAINTENANCE
G250A01A-AAT
FOR MORE INFORMATION ABOUT
FOR MORE INFORMATION ABOUT
FOR MORE INFORMATION ABOUT
FOR MORE INFORMATION ABOUT
FOR MORE INFORMATION ABOUT
YOUR HYUNDAI
YOUR HYUNDAI
YOUR HYUNDAI
YOUR HYUNDAI
YOUR HYUNDAI
If you desire additional information about main-
taining and servicing your Hyundai, you may
purchase a factory Shop Manual at your Hyundai
dealer's parts department. This is the same
manual used by dealership technicians and
while it is highly technical it can be useful in
obtaining a better understanding of your car
and how it works.
G260A01A-AAT
REPLACING LIGHT BULBS
REPLACING LIGHT BULBS
REPLACING LIGHT BULBS
REPLACING LIGHT BULBS
REPLACING LIGHT BULBS
Before attempting to replace a light bulb, be
sure the switch is turned to the "OFF" position.
The drawing in the next paragraph shows how
to reach light bulbs so they may be changed.
Be sure to replace the burned-out bulb with one
of the same number and wattage rating.
G270A02A-GAT
HEADLIGHT BULB
HEADLIGHT BULB
HEADLIGHT BULB
HEADLIGHT BULB
HEADLIGHT BULB
Replacement instructions:
Replacement instructions:
Replacement instructions:
Replacement instructions:
Replacement instructions:
1. Allow the bulb to cool. Wear eye protection.
2. Always grasp the bulb by its plastic base,
avoid touching the glass.
3. Disconnect the power cord from the bulb
base in the back of the headlight.
4. Remove the dust cover.
5. Push the bulb spring for removing the head-
light bulb.
6. Remove the protective cap from the re-
placement bulb and install the new bulb by
matching the plastic base with the headlight
hole. Install the dust cover after retightening
the bulb spring and reconnect the power
cord.
7. Use the protective cap and carton to dis-
pose of the old bulb.
8. Check for proper headlight aim.
AX60380A
6-17
Hide quick links:
Advertisement
Table of Contents
