Advertisement
15. Stand your iron vertically on the charging base and let the iron heat for two
minutes to ensure that the iron is dried out completely.
16. After use, switch off and unplug your iron from the mains supply and allow it to
fully cool before storing.
Cleaning the steam holes
To remove any build-up in or around the steam holes which may affect steam
performance, use a cotton wool tip moistened with methylated spirits. Wipe off the
methylated spirits with a damp cloth then dry the soleplate.
Cleaning the exterior of your iron
To clean the exterior of your iron and charging base, wipe it with a soft damp cloth and
wipe dry.
Storing
Warning: Allow your iron to completely cool before storing. Always store your iron on its
heel rest. Do not store your iron resting on its soleplate.
The SAFE-STORE™ heat indicator shows you when the soleplate of your iron has
cooled sufficiently for it to be safe to store. If the strip is red, your iron is too hot. When
the words SAFE-STORE appear on the strip against a solid black background, the
soleplate is at a safe temperature for storing.
Never wrap the power cord around the soleplate. The cord can be neatly wrapped
around the heel of your iron.
After sales service and replacement parts
In the case the appliance does not operate but is under warranty, return the product
to the place it was purchased for a replacement. Please be aware that a valid form of
proof of purchase will be required. For additional support, please contact our Consumer
Service Department at 0800 028 7154 or email: BrevilleEurope@newellco.com.
8
VIN439_22EM1 (UK).indd 8-9
VIN439_22EM1 (UK).indd 8-9
Troubleshooting
For troubleshooting and FAQs visit www.breville.co.uk/faqs.
PROBLEM
CAUSE
Iron is not
The appliance is not
heating.
plugged in, docked onto
the charging base, or not
switched on.
The appliance is in auto-
off mode.
Iron will not
Insufficient water in the
steam.
tank.
The steam control is in
the no steam position
The iron has not been
primed before first use.
Steam rate
Calc build up.
decreases.
Iron is
The water tank has been
leaking.
filled above the MAX
level.
Shot of steam button
has been pressed too
frequently.
The water tank is not
fully in place, or the fill
inlet cover is not closed
properly.
Water has been left in
the water tank during
storage.
The steam
You are using water with
leaves
additives.
stains on the
The appliance has not
fabric or the
been cleaned enough
appliance
after the descaling
spits.
operation.
Water has been left in
the water tank during
storage.
You are using liquids
other than water to
descale the product.
Impurities are in the
water used to fill the iron.
Wrinkles
Temperature selected
are not
is too low for the fabric
sufficiently
being iron.
removed.
Ironing thicker fabrics
like cotton/linen.
Fabrics are
Fabric has been ironed at
getting an
too high a temperature.
unwanted
shine.
SOLUTION
Check that unit is plugged into the
charging base and that the electrical
cord is plugged into a working
electrical outlet.
Verify the auto-off function is not
active. Refer to the 'Auto shut off
feature' section.
Ensure water tank level is at least
¼ full.
Adjust the steam control to the
correct setting for your garment.
.
Press shot of steam button several
times to prime.
Use self-cleaning feature once a
month. Refer to the 'Self-cleaning'
section.
Only fill with water to the MAX level.
Only use the shot of steam in
3-second intervals or less.
Ensure that the fill inlet cover is
closed and that the water tank
snaps when put into place.
Empty the water reservoir after each
use and move steam control to the
no steam position setting.
Never add any additive in the water
tank.
Use self-cleaning feature once a
month. Refer to the 'Self-cleaning'
section.
Empty water tank completely after
each use.
Use only water during descaling
operation. We recommend using
distilled water.
Ensure water cup used to fill the
iron is clean.
Check that the temperature control
dial is set to the correct fabric
setting.
Use shot of steam or spray mist
features to help remove stubborn
wrinkles.
Reduce the temperature setting.
Use an ironing cloth or a 100%
white cotton fabric and place it
between the garment being ironed
and the iron to prevent shine.
2022/4/28 上午10:03
2022/4/28 上午10:03
9
Advertisement
