Advertisement
5.
Adjust the steam control (3) to select the
desired steam output. To use the max steam
setting, push and hold the steam control
towards the setting (Figure 3).
6.
The steam can be shut off at any time by
setting the steam control to the no steam
position.
7.
Unlock the iron from the charging base (8) by
moving the lock/unlock base switch (9) to the
unlocked position
.
8.
Hold the iron by the handle and remove from the base (Figure 2). The
temperature indicator light (6) will turn off when undocked.
9.
Start ironing.
10. Return the iron onto the charging base every few seconds to re-heat the
soleplate.
11. The the temperature indicator light (6) will illuminate red to indicate the iron is
reheating and turn green when ready to use.
12. Alternatively, move the lock/unlock base switch to the locked position
iron in corded mode.
Note: Dripping from the soleplate may occur if the max steam setting is used
continuously in cordless mode. The iron will need to be returned to the charging base
more frequently to re-heat.
Shot of steam
1.
The temperature control dial (10) must be set within the •• and ••• setting.
2.
The water reservoir must be at least ¼ full of water.
3.
Press the shot of steam button (5) whenever you have a stubborn crease that
needs extra steam. Steam will burst from the holes in the soleplate of your iron
into the fabric.
4.
The shot of steam button may be used continuously in approximately 3-second
intervals Dripping from the soleplate may occur when the shot of steam button is
pressed too frequently. If ironing in cordless mode, return the iron to the charging
base every few seconds to reheat.
Vertical steam ironing
Never iron garments when they are being worn.
1.
Prepare your iron as for steam ironing.
2.
Hold your iron 15cm from the fabric.
3.
Press the shot of steam button (5) as required. Wait several seconds between
each press of the button.
4.
If ironing in cordless mode, return the iron to the charging base every few
seconds to reheat.
Spray Mist
The water spray can be used to help iron heavy fabrics or difficult areas (collars,
pockets, sleeves, creases, etc). It can also be used when ironing delicate fabrics which
cannot be steam ironed.
Make sure there is water in the tank. Press the spray mist button (4) to produce a spray
of water.
Anti-drip feature
When the temperature of your iron is insufficient to create steam, the supply of water is
cut off automatically to avoid any drips from the soleplate.
Anti-scale filter
Your iron is fitted with a permanent anti-scale filter. This filter is fixed and cannot be
removed for cleaning.
6
VIN439_22EM1 (UK).indd 6-7
VIN439_22EM1 (UK).indd 6-7
The filter is designed to reduce the build-up of limescale inside your iron. Limescale
occurs during steam ironing due to water hardness.
Water hardness varies from one area to another. The effectiveness of the filter will
depend on how 'hard' your water is.
Auto shut off feature
ALWAYS disconnect your iron from the mains supply socket after use. NEVER leave
Figure 3
the iron unattended with the auto shut off function in operation.
An electronic safety device will automatically switch the heating element off if the iron
has not been moved more than 30 seconds when resting on its soleplate in a horizontal
position.
If resting on its heel in a vertical position, this will happen after 15 minutes.
The temperature ready indicator will blink red when auto-off is activated. Note: The
temperature ready indicator will blink only if the iron is docked onto the charging base.
To restart your iron, gently move it until the light stops flashing and reheat until the
temperature ready indicator illuminates green.
to use the
Care and cleaning
Warning: Do not use harsh abrasives, chemical cleaners or solvents to clean the
exterior of your iron and charging base.
Allow your iron to completely cool down and wipe the soleplate with a soft damp cloth. If
polyester has burnt to the soleplate, iron a damp cotton cloth while your iron is still hot.
Wipe over the rest of your iron with a soft damp cloth then wipe dry.
Do not immerse the appliance, charging base or power cord or plug in water or any
other liquid.
Self-cleaning
Only press the self-clean lever (3) when you want to activate the self-cleaning
system. Never press the self-clean lever when ironing.
The self-clean function removes scale and impurities. Use the self-clean function once
every two weeks. If the water in your area is very hard, the self-clean function should be
used more frequently.
1.
Ensure your iron is switched off and unplugged from the mains supply socket.
2.
Set the steam control (3) to the
3.
Fill your iron with water to the MAX level.
4.
Dock the iron in the vertical position onto the charging base (8).
5.
Move the lock/unlock base switch to the locked position
iron from the charging base during the cleaning process.
6.
Plug in and switch on at the mains supply.
7.
Set the temperature control dial (10) to the highest (MAX) setting. Allow your iron
to heat up until the temperature indicator light illuminates green.
8.
Unplug your iron from the mains and hold it over a sink with the soleplate facing
downwards.
9.
Push and hold the steam control lever (3) to the self-clean position. Hot water and
steam will be ejected from the holes in the soleplate along with any impurities.
10. Slowly rock the iron side-to-side and front to back for 30 seconds. When rocking
the iron, dip the nose of the iron slightly below the rear to make certain the water
circulates completely.
11. Release the self-clean lever (3) after 30 seconds and pour out the remaining
water out of the fill hole.
12. Rest the iron soleplate horizontally on an old piece of cloth (cotton or towels are
ideal) to dry.
13. Plug in the iron and turn the temperature control dial to the ••• setting.
14. When the temperate indicator light illuminates green, iron an old piece of cloth to
allow any remaining water to escape.
no steam position.
Warning: Be careful not to touch the iron's hot surfaces.
. Do not release the
7
2022/4/28 上午10:03
2022/4/28 上午10:03
Advertisement
