Advertisement
Cleaning your iron before use
Follow these simple steps to remove any impurities or residues inside your steam iron
that may be left over from the manufacturing process.
1.
Follow the instructions under filling your iron and fill the water tank as described.
2.
Empty the water tank to rinse out any foreign particles then refill it.
3.
Follow the instructions under steam ironing. Set the temperature to the MAX
setting and the steam control to the high steam setting.
4.
Iron an old piece of cloth (cotton or towels are ideal) for a few minutes. While
ironing, press the steam button 4 or 5 times.
5.
Any impurities will be flushed from your iron by the steam and absorbed by the
cloth. Your iron is now ready for use.
Filling your iron
1.
Ensure your iron is switched off and unplugged from the mains supply socket.
2.
Set the steam control (3) to the no steam position
3.
Open the water tank inlet cover.
4.
Using a jug, fill the water tank with ordinary tap water. To avoid air locks, tilt your
iron slightly while filling it.
5.
Don't fill the iron above the water level indicator MAX marking. Check the water
level by standing the iron on its heel.
6.
When the iron is filled, ensure the water tank inlet cover is fully closed and sealed
to prevent water leaking out when the iron is in use.
Ironing in corded mode
1.
Dock the iron in the vertical position onto the charging base (8).
2.
Move the lock/unlock base switch to the locked position .
3.
To ensure the iron is locked into place, rotate the iron on the charging base until
an audible clicking sound is heard and the heel is aligned with the base.
4.
Lift the iron by the handle to ensure that it is securely locked onto the base (Figure
1).
5.
Keep the iron on the heel rest of the charging base when not ironing.
Ironing in cordless mode
1.
Dock the iron in the vertical position onto the charging base (8).
2.
When the iron is charging, the temperature indicator light (6) will illuminate red.
For first use, wait until the temperature indicator light illuminates green; then the
iron is ready for use.
3.
Unlock the iron from the charging base (8) by moving the lock/unlock base switch
(9) to the unlocked position
.
4.
Hold the iron by the handle and remove from the base (Figure 2). The temperature
indicator light (6) will turn off when undocked.
5.
Start ironing.
6.
Return the iron onto the charging base every few seconds to re-heat the soleplate.
7.
The the temperature indicator light (6) will illuminate red to indicate the iron is
reheating and turn green when ready to use.
4
VIN439_22EM1 (UK).indd 4-5
VIN439_22EM1 (UK).indd 4-5
.
Figure 1
IMPORTANT: When using the shot of steam feature, your iron might cool down faster;
therefore, it might take additional time to reheat.
NOTE: The Turbo Charge Corded Cordless Iron is NOT a rechargeable device with a
battery. You cannot continuously use this iron without placing it on the charging base to
reheat the soleplate.
Ironing without steam
If you intend to dry-iron fabrics there is no need to fill the water tank. However, if water
is already in the water tank, you don't need to empty it.
1.
Set the steam control (3) to the no steam position .
2.
With your iron locked onto the charging base (8), plug your iron into the mains
supply and switch on.
3.
Rotate the temperature control dial (10) until the desired setting is aligned with
the dial pointer.
4.
When the iron is charging, the temperature indicator light (6) will illuminate red.
When the light turns to green, your iron is ready to use.
5.
Unlock the iron from the charging base (8) by moving the lock/unlock base
switch (9) to the unlocked position
6.
Hold the iron by the handle and remove from the base (Figure 2). The
temperature indicator light (6) will turn off when undocked.
7.
Start ironing.
8.
Return the iron onto the charging base every few seconds to re-heat the
soleplate.
9.
The the temperature indicator light (6) will illuminate red to indicate the iron is
reheating and turn green when ready to use.
10. Alternatively, move the lock/unlock base switch to the locked position
the iron in corded mode.
Steam ironing
During steam ironing, if you do not allow your iron to reach the selected
temperature water may drip from the soleplate.
It is recommended that for harder to iron fabrics such as cotton and linen, steam
should be used when ironing.
When ironing cotton and linen, always select the highest temperature. Steam should
never be used on delicate fabrics like nylons, acrylics and synthetics.
1.
Fill your iron with water. The water reservoir must be at least ¼ full of water.
2.
With your iron locked onto the charging base (8), plug your iron into the mains
supply and switch on.
3.
Set the temperature control dial (10) to the •• or ••• setting. The hotter your iron,
the more steam is generated.
4.
When the iron is charging, the temperature indicator light (6) will illuminate red.
When the light turns to green, your iron is ready to use.
Figure 2
.
to use
2022/4/28 上午10:03
2022/4/28 上午10:03
5
Advertisement
