Page 2
Find manuals at https://best-manuals.com...
Page 3
PERSONAL SAFETY THIS SAFETY ALERT SYMBOL INDICATES IMPORTANT SAFETY MESSAGES IN THIS MANUAL. WHEN YOU SEE THIS SYMBOL, CAREFULLY READ THE MESSAGE THAT FOLLOWS AND BE ALERT TO THE POSSIBILITY OF DEATH OR SERIOUS INJURY. M171C Throughout this manual and on the machine’s safety decals, you will find precautionary statements: DANGER, WARNING or CAUTION followed by specific instructions or ISO two panel safety pictorial symbols.
Page 4
CNH America LLC Technical Manuals Manuals are available from your Dealer for the operation, service and repair of your machine. For prompt convenient service, contact your Dealer for assistance in obtaining the manuals for your machine. Your Dealer can expedite your order for Operator’s Manuals, Parts Catalogs, Repair Manuals and maintenance records.
Page 5
PUBLICATION HISTORY MACHINE PUBLICATION ISSUE DATE ISSUE ® AXIAL-FLOW 5088, 6088 and 7088 Combine 87479245 September, 2008 First Issue Find manuals at https://best-manuals.com...
Page 6
Find manuals at https://best-manuals.com...
Template Name: OML_2_col Rac 0-00000 Template Date: 2001_03_06 1 - TO THE OWNER ® AXIAL-FLOW COMBINE RH08E034 NOTE: When you are in the Combine seat looking forward, the right and left side of the Combine are the DEALER’S STAMP same as your right hand and left hand. 522L94 CNH America, LLC 700 State Street...
If your Combine is equipped with AFS Yield Monitor required for this machine to comply with various and/or AccuGuide™ refer to your CASE IH Yield countr y regulations and safety requirements. Monitor, AFS Pro 600™ or AccuGuide™ Manual(s) Unauthorized modifications will cause serious injury for operating instructions.
Template Name: OML_2_col Rac 0-00000 Template Date: 2001_03_06 2 - IDENTIFICATION NUMBERS PRODUCT IDENTIFICATION AND SERIAL NUMBERS Write your machine model number and Product Identification Number (P.I.N.) and Serial Numbers of major components on the lines provided. If needed, give these numbers to your dealer when you need parts or information for your machine.
Page 14
2 - IDENTIFICATION NUMBERS Engine Serial Number RD07G025 Combine Model Number________________________________________________________________ Product Identification Number____________________________________________________________ Engine Serial Number___________________________________________________________________...
2 - IDENTIFICATION NUMBERS MACHINE MAIN COMPONENTS RH08E034 1. FEEDER HOUSING 7. LEFT SIDE PANELS 2. OPERATOR’S CAB 8. BATTERY COMPARTMENT 3. LEFT SIDE SERVICE DOOR 9. OPERATOR’S LADDER 4. FRONT HEAD LAMPS 10. OPERATOR’S PLATFORM 5. GRAIN TANK 11. REAR VIEW MIRROR 6.
Page 16
2 - IDENTIFICATION NUMBERS RH08E036 1. ENGINE COMPARTMENT 6. OPERATOR’S PLATFORM HANDRAILS 2. RIGHT SIDE PANELS 7. ELEVATORS 3. RIGHT SIDE SERVICE DOOR 8. STATIONARY AIR SCREEN 4. ROTOR HOUSING (INTERNAL) 9. RIGHT SIDE OPERATOR’S PLATFORM 5. SERVICE LADDER 10. REAR BEACON Rh08e038 11.
Template Name: OML_2_col Rac 0-00000 Template Date: 2001_03_06 3 - SAFETY/DECALS SAFETY Understand that your safety and the safety of other persons is measured by how you operate and service this machine. Know the positions and operations of all controls before you try to operate them. MAKE SURE YOU CHECK ALL CONTROLS IN A SAFE AREA BEFORE STARTING YOUR WORK.
Page 18
3 - SAFETY/DECALS Never operate the engine in a closed building. Proper ventilation is required under all circumstances. R142A Check and service cooling system according to maintenance instructions. Hot coolant can spray out if deaeration tank cap is removed while system is hot. To remove deaeration tank cap, let system cool, turn to first notch, then wait until all pressure is released.
Page 19
3 - SAFETY/DECALS Feeder Safety Lock The left feeder lift cylinder is equipped with a safety lock. The safety lock is used to prevent accidental lowering of the feeder or Header. ALWAYS engage the feeder safety lock before working under the feeder or Header. To Engage the Feeder Safety Lock: 1.
Page 20
3 - SAFETY/DECALS FIRE AND EXPLOSION PREVENTION Due to the flammable nature of the crop materials encountered by Combine, fire risks are high. This risk can be minimized by frequent removal of accumulated crop material from the machine and checking for overheated machine components.
Page 21
3 - SAFETY/DECALS LADDER SAFETY Always use access ladder only after the Combine has come to a complete stop. Always face the Combine when using the access ladders. Always make sure ladder safety chains are properly connected. Make sure rear access ladder is UP during field operation. Always position cab access ladder to the FORWARD position when transporting the Combine.
3 - SAFETY/DECALS FIRE EXTINGUISHER Ri08b167 SERVICE COMPARTMENT A fire extinguisher is equipped on your machine in the left hand service compartment on the operator’s platform. Make sure the fire extinguisher is maintained and on the Combine during field operation to assist in the event of a fire.
3 - SAFETY/DECALS FIRE PREVENTION Fire Sources The possibility of accidental fires is ever present Your best defense against potential fires on your during the harvest. The three ingredients needed for machine is to know how to minimize the potential a fire - combustible materials, oxygen and a potential through proper adjustment, operation, maintenance source of ignition - are always present during the...
3 - SAFETY/DECALS PARK BRAKE RD07G026 PARK BRAKE SWITCH - To engage the Park Brake push front half of the switch. To disengage the Parking Brake push rear half of the switch.
3 - SAFETY/DECALS Battery Safety DO NOT make sparks or use an open flame near the battery. When disconnecting battery terminals, remove the Negative (-) cable first; then remove the Positive (+). When connecting cables, connect the Positive (+) first, then connect the Negative (-). Disconnect the battery (both terminals) before welding on any part of the machine.
Page 26
3 - SAFETY/DECALS Maintenance Safety Always keep safety and informational decals clean and visible. Replace decals that are damaged, lost, painted over or can not be read. When assembling, operating or servicing the machine, wear protective clothing and personal safety devices that are necessary for the particular procedure.
3 - SAFETY/DECALS HAZARD WARNING LAMP/PARK BRAKE DISABLE SWITCH HAZARD WARNING LAMP/PARK BRAKE DISABLE SWITCH - Push the upper half of the switch to the CENTER position to activate the amber warning lamps. Push the bottom half of the switch to turn OFF the warning lamps.
3 - SAFETY/DECALS HIGHWAY OPERATION WARNING: On narrow or hilly roads or blind curves where motor vehicles can suddenly come upon slow moving traffic, extra caution should be exercised, such as having two vehicles proceed/follow the Combine to warn and/or removing the Header and transport separately. M751 1.
Page 29
3 - SAFETY/DECALS Front Lighting RD08E029 RH08E031 LEFT HAND EUROPEAN LIGHTING RIGHT HAND EUROPEAN LIGHTING CONFIGURATION CONFIGURATION Travel Speed - Germany Only RH08A016 RH08A017 20 KPH DECAL - REAR 20 KPH DECAL - LEFT SIDE...
Page 30
3 - SAFETY/DECALS Tire Chocks - Germany Only Rear View Mirror - Germany Only RH08A015 Rd06D153 MIRROR MOUNTED ON RIGHT HAND RAIL Instructional Seat Safety Extra riders, especially children, A. Machine must be driven at a slower speed permitted on the machine. and on level ground.
3 - SAFETY/DECALS SEAT BELTS The Operator and Instructor should securely fasten the seat belts before the Combine is operated either in the field or on the road. NOTE: The illustrations below show an Instructional Seat Belt. Operator Seat Belt is the same. RP95J008 RP95J014 1.
3 - SAFETY/DECALS NEUTRAL START SYSTEM Make sure the Neutral Start System is operating 2. If engine does start, Neutral Start System needs properly by doing the following: adjustment. See your dealer. 1. With the propulsion handle in a position other than Neutral, the engine should not start.
3 - SAFETY/DECALS SAFETY AND INFORMATIONAL DECALS IMPORTANT: Install new decals if the old decals are destroyed, lost, painted over or cannot be read. When parts are replaced that have decals make sure you install a new decal with each new part. NOTE: New decals are available from your dealer.
Page 35
3 - SAFETY/DECALS RI08C031 RI08B172 Machine Clearance - Electrocution Hazard 429497A Operator’s Manual Location On Right Hand Armrest 371078A Do Not Block Recirculation Filter On Rear Cab Wall...
Page 36
3 - SAFETY/DECALS RI08B167 RI08B152 Oil Type - On Base Of Grain Tank Near Fill Neck RI08B151 Jack Lift Point RH97G045 182270A1 T-Hook Tie Down Location Avoid Falls...
Page 37
3 - SAFETY/DECALS RI08B167 RI08B194 Fire Extinguisher 144384A1 Do Not Enter Grain Tank (Centered On Inside Of Door)
Page 38
3 - SAFETY/DECALS RI08B168 RI08B151 Caution Tie Down Point RI08B151 Caution Jack Point...
Page 39
3 - SAFETY/DECALS RI08B168 RI08B159 Use Case IH 135 HEP RI08C044 Ladder Hazard - Stay Clear RI00H088 Hydraulic Fluid Level...
Page 40
3 - SAFETY/DECALS RI08B168 87488845 Lubrication Points 144384A1 Do Not Enter Grain Tank...
Page 41
This as a preview PDF file from best-manuals.com Download full PDF manual at best-manuals.com...
Need help?
Do you have a question about the Axial-Flow 5088 and is the answer not in the manual?
Questions and answers