Related Manuals for BAFANG H610
Summary of Contents for BAFANG H610
- Page 1 USER MANUAL H610 Drive System Original instruction manual Read carefully before use. Keep for later reference. BF-UM-S-H610-1-EN-PRINT, November 2019...
-
Page 2: Table Of Contents
SYMBOL INSTRUCTION If you see the following symbols there is always a Danger: This symbol indicates possible health and safety hazards that may arise, if certain possibility of danger. measures are not taken into consideration. The warning symbols are as follows: User Manual: Please read the manual before Note: This symbol indicates information about using the pedelec. -
Page 3: Guide
1 GUIDE 1.1 Quick start This section provides important information and instructions that will allow you to use your pedelec in a safe manner. First, please read the safety instructions to find out about the legal regulations that apply to you. Perform all safety checks in accordance Practice using the pedelec in a quiet and safe with the "Before each trip"... -
Page 4: Important Notice
2 IMPORTANT NOTICE 2.2 Pedelec modifications Be sure to follow the instructions in the manual when using this product. are prohibited • If you are lending your pedelec to third par- ties, please give them the instruction manual Do not change the pedelec drive system in any along with the pedelec. - Page 5 The authorized retailer can only use the original spare parts Before driving on public roads, please read the from Bafang for maintenance. applicable countries regulations carefully. The use of pedelecs on public roads must comply with Do not use no high-pressure water jet or local regulations.
-
Page 6: Vehicle Transport
3 VEHICLE TRANSPORT Remove the battery during transport and store When transporting the pedelec by train, the relevant laws and regulations must be complied the battery in a safe and dry place. with. Before using public transport, please find Do not transport a battery without the correct out which means of transport are suitable for procedure. -
Page 7: Guaranty
5 GUARANTY All warranty and guarantee conditions are Warranty and warranty exclusions: subject to applicable laws and regulations from • Modification, manipulation or improper your brand. repair of the product. The condition for warranty and guarantee • Improper use of the product. claims is that the instructions for the system are •... - Page 8 6 USER MANUAL FOR H610 (FM G070.250/350/500.D) CONTENT 6.1 Introduction 6.2 Specifications 6.2.1 Surface 6.2.2 Storage Information 6.3 Maintenance BF-UM-C-FM G070-D-EN November 2019...
-
Page 9: Introduction
6.1 INTRODUCTION • Scope Applies only to electrically powered pedelecs developed or licensed by Bafang. It is suitable for bikes, which have been developed for the city road, off road on gravel or sand use. The engine is not suitable for sport competitions. -
Page 10: Specifications
6.2 SPECIFICATIONS Motor model: FM G070.250.D / FM G070.350.D / FM G070.500.D Rated power (W) 250 / 350 / 500 Rated voltage (V) 36 / 43 / 48 Waterproof IPX5 Certification CE-EMC Outdoor Temperatures -20℃~45℃ 6.2.1 Surface Shockproof black and silver coating 6.2.2 Storage Information The pedelec should be stored in a ventilated dry room. -
Page 11: Maintenance
6.3 MAINTENANCE • Maintenance must be carried out by autho- rized personnel with the correct equipment. • Do not disassemble the motor. • Do not use thinners or other solvents to clean the components. Such substances can damage the surfaces. •... - Page 12 7 USER MANUAL FOR DP C171.CAN CONTENT 7.1 Important Notice 7.6.3 Selection mode 7.2 Introduction of Display 7.6.4 Headlights / backlighting 7.3 Product Description 7.6.5 Walk Assistance 7.6.6 Battery capacity indication 7.3.1 Specifications 7.6.7 USB charge function 7.3.2 Functions Overview 7.7 Settings 7.4 Display 7.5 Key Definition...
-
Page 13: Important Notice
7.1 IMPORTANT NOTICE • If the error information from the display • Please use this product with care. cannot be corrected according to the inst- • Do not use thinners or other solvents to ructions, please contact your retailer. clean the display. Such substances can •... -
Page 14: Product Description
• Service • USB charge function • Bluetooth function (it can be connected to the phone to use the Bafang Go APP). • The SEGMA heart rate monitor can be con- nected to display the heart rate in real time. -
Page 15: Display
7.4 DISPLAY Display of battery capacity in real time. Menu. Service: please see the service section. Digital speed display. Speed mode , top speed (MAXS) - Average speed (AVG). Kilometer stand, Daily kilometers (TRIP) - Total kilometers (TOTAL). Data: Display data, which corresponds to the current mode. -
Page 16: Key Definition
7.5 KEY DEFINITION Light On/Off System On/Off Down OK/Enter 7.6 NORMAL OPERATION 7.6.1 Switching the System ON/OFF Press and hold (>2S) on the display to turn on the system. Press and hold (>2S) again to turn off the system. If the "automatic shutdown time" is set to 5 minutes (it can be set with the "Auto Off" function, See "Auto Off"), the display will automatically be turned off within the desired time when it is not in operation. -
Page 17: Selection Mode
7.6.3 Selection mode Briefly press (<0.5s) the button to see the different trip modes. Trip: daily kilometers (TRIP) - to- tal kilometers (TOTAL) - Maximum speed (MAXS) - Average speed (AVG) - Remaining distance (RANGE) - Output power (W) - Energy consumption (C (only with torque sensor fitted)). 7.6.4 Headlights / backlighting Hold (>2S) the button to activate the headlight and backlight. -
Page 18: Walk Assistance
7.6.8 Bluetooth function This display can connect via Bluetooth to mobile phone and communicate with Bafang Go APP. The Information of motor, display, battery, sensor and controller infor- Bars Charge in Percentage mation can be displayed on mobile phone, and it can update the firmware of Pedelec by ≥90%... -
Page 19: Settings
7.7 SETTINGS After the display is turned on, quickly press (<0.3S) the button twice to access the “MENU” interface. pressing the button, you can select and reset the options. Then press (<0.3S) the button twice to confirm your selected option and to return to the main screen. - Page 20 sensitivity for 0-5). Chose 0 means turn off button until the “OFF” appears on the the light sensitivity. display (as shown below). And then press Once you have chosen your desired selec- to increase or to reduce (brightness tion, press (<0.3S) the button twice for 1-9minute).
-
Page 21: View Information
7.7.2 View Information All data in this item cannot be changed, only to be viewed. 7.7.2.1 Wheel Size When the system is on, quickly press (<0.3S) the button twice to access the “MENU” interface, repetitively press the button until the “LUd” appears on the display (as shown below). - Page 22 Once you have viewed your desired informa- the “MENU” interface, repetitively press the tion, press (<0.3S) the button twice to button until the “dSc (Display Software save and return to the main screen, or you check)” appears on the display (as shown can press (<0.3S) the button once to below).
- Page 23 7.7.2.8 BMS software info When the system is on, quickly press (<0.3S) the button twice to access the “MENU” interface, repetitively press the button until the “dSc (Display Software check)” appears on the display (as shown below). Once you have viewed your desired informa- tion, press (<0.3S) the button twice to save and return to the main screen, or you...
- Page 24 7.7.2.11 Battery Information Content Explanation When the system is on, quickly press Charging cycles (number) (<0.3S) the button twice to access the “MENU” interface, repetitively press the Maximum not charging time (Hr) button until the “b01” appears on the Recently not charging time (Hr) display (as shown below).
-
Page 25: Error Code Definition
7.8 ERROR CODE DEFINITION The display can show the errors of a pedelec. If an error is detected, the wrench icon appears on the display and one of the following error codes will be displayed. Note: Please read carefully the description of the error code. When the error code appears, please first restart the system. - Page 26 Error Declaration Troubleshooting 1. Turn off the system and let the pedelec cool The protection temperature inside down. the controller has reached its maxi- 2. If the problem persists, please contact your mum protection value retailer. Error with the temperature sensor Please contact your retailer.
- Page 27 Error Declaration Troubleshooting Detection circuit for 15V has an error Please contact your retailer. Detection circuit on the keypad has Please contact your retailer. an error WDT circuit is faulty Please contact your retailer. Total voltage from the battery is too Please contact your retailer.