Advertisement
Confi guration & Specifi cations
ShoreGear 220T1A Voice Switch RJ-21X Port Pinout
An RJ-21 telephone cable, wired straight through, allows the ShoreGear 220T1A Voice
Switch to connect to a standard 12-port patch panel or 12-port harmonica block. When
connecting to a 24-port patch panel, the voice switch' s six analog extension ports map to
ports 1 and 3 and ports 17, 19, 21, and 23 on the patch panel. The Power Fail Transfer
Unit provides an electrical connection between trunk channel 1 and the extension on
channel 12.
1 2 3
4
5
6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25
Pin No.
Port No.
1
2
Port Type
T
T
26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50
Pin No.
Pin pairs
Assignment
1,26 3,28
Two loop start ports (T) for trunks.
17,42 19,44 21,46 23,48
Four confi gurable ports (E) for telephones or DID trunks.
Network Confi guration
Once the ShoreGear voice switch is installed and powered on, it must be confi gured for
network operations. A voice switch gets a network confi guration by assignment from a
DHCP or BOOTP server, or directly from an administrator console (see procedure below).
For more information on setting up a switch for automatic confi guration by a DHCP or
BOOTP server, see the ShoreTel Planning and Installation Guide.
Confi guring the Voice Switch from a Console
Use a straight-through serial cable, DB9 male to DB9 female, to connect the switch to a
1.
console PC.
On the PC or laptop, start a terminal emulation program and connect to the voice
2.
switch using these serial communication settings: 19200 bps, 8 data bits, no parity,
one stop bit, no handshake.
At the ShoreTel login prompt, press ENTER to display the Switch Options menu.
3.
Type 3 and press ENTER to display a menu of confi guration options.
4.
Choose Menu Options and follow the onscreen instructions for setting network
5.
parameters, including IP address, subnet mask, and gateway.
Specifi cations
Feature
Specifi cation
Dimensions
1.69 x 8.39 x 14.28 inches (43 x 213 x 378)
Weight
5.3 lb (2.4 kg)
Input voltage
100-240 VAC, 50-60 Hz
Power consumption
1A max.
Humidity
0-90% relative humidity (non-condensing)
Operating temperature
0-50˚ C
PN 850-1114-01
Switch Status
Power LED
The power LED indicates the operating status of the switch.
Light
Description
Steady
The switch is powered on, and the internal software is running.
Flashing
Two fl ashes indicates a failed internal self-test (i.e. hardware failure). Refer to "Confi guring
Switches" in the ShoreTel Administration Guide for details on other fl ash patterns.
Off
The switch is not powered on, or the software is not running.
X
9
10
11
12
Status LED
X
E
E
E
E
The status LED provides voice switch activity information.
Color
Activity
Off
Green
Steady
Green
Flashing-Fast
Yellow
Steady
Yellow
Flashing-Slow
Yellow
Flashing-Fast
Network LEDs
Each LAN connector provides two LEDs (Link/Act and 100) that indicates the activity
and communication speed of the connected network.
LED
Color/State
Link/Act
Off
Link/Act
Green-Steady
Link/Act
Green-Flashing
100
Off
100
Green
T1 LEDs
The T1 LEDs indicate line coding, network framing, and loopback status.
LED
Color/State
Line coding
Green
Line coding
Yellow
Line coding
Red
Line coding
Off
Framing
Green
Framing
Yellow
Framing
Yellow-Flashing
Framing
Red
Framing
Off
LC/Framing
Red-Flashing
Copyright © 2007 ShoreTel. All rights reserved. ShoreTel, the ShoreTel logo, ShoreGear,
ShoreWare, and ShorePhone are trademarks of ShoreTel, Inc. in the United States and/or other
countries. All specifi cations are subject to change without notice. This product is covered by one or
more of the following patents: United States Patent 6,996,059,United States Patent 7,003,091, and
United States Patent 7,167,486. ShoreTel, Inc. All rights reserved.
Description
No ports are assigned
No ports are handling active calls
At least one port is handling an active call.
No ports are handling active calls and at least one port is out of service.
The switch is not connected (or has lost connection) to a ShoreTel server.
At least one port is handling an active call and at least one port is out of
service.
Description
This switch cannot detect an Ethernet network.
This switch is connected to an Ethernet network.
This switch detects network data traffi c.
Network interface is operating at 10 Mbps.
Network interface is operating at 100 Mbps.
Description
The AMI or B8ZS line coding signal is good.
This switch is receiving bipolar violations (BPV) at one-second intervals.
A loss of signal (LOS) has occurred.
The switch has no power.
The T1 signal is in frame (synchronized)
The CO has sent a yellow alarm.
The frame-bit error rate has exceeded its limits
T1 signal is out-of-frame (OOF) and cannot be framed to the Extended
Superframe (ESF) or D4 format.
This switch has no power.
Loopback is enabled. (Loopback can be set from Shoreline Director or
at the CO).
ShoreGear 220T1A Voice Switch
Quick Install Guide
960 Stewart Drive Sunnyvale, California 94085
Phone: +1.408.331.3300 OR +1.800.425.9385 Fax: +1.408.331.3333 www.shoretel.com
Advertisement
