ShoreTel ShoreGear 220T1A Quick Install Manual

Introduction
The ShoreGear 220T1A Voice Switch package contains:
• ShoreGear 220T1A Voice Switch
• Power cord
• Stick-on feet for surface installation
• Mounting Ears – attachable installation brackets
• Cable Retainer for the Telco cable (metal bracket with a Velcro strap)
About The ShoreGear 220T1A
The ShoreGear 220T1A Voice Switch connects internal extensions or IP phones to a
central office (CO) digital trunk line.
The switch provides connectivity through:
• Two RJ-45 LAN connectors
• One RJ-45 T1 port for connecting the switch to a telephone company line
• One RJ-45 T1 monitor port for connecting test equipment
• One RJ-21X port (male) for connecting the switch to a telephone company punch-
down block, patch panel, or 12-port harmonica connector
• One DB-9 (female), RS-232C maintenance port (19200 bps, 8 bits, no parity, 1 stop
bit, no handshake) for serial communications
• One audio input port (3.5 mm stereo) for connecting to a music-on-hold source
• One audio output port (3.5 mm stereo) for connecting to a corporate paging system or
night bell
Audio Input Port
(music on hold)
Status Network LAN 1 T1 Telco
T1 LEDs
LED LEDs Connector
Default
Switch
Power Network RS-232C T1 LEDs
LED LEDs Maintentance
Port
Audio Output Port LAN 2 T1 Monitor
(night bell) Connector Port
Installation Equipment
To install the switch, you need the following equipment:
• AC surge protector for the power connection
• RJ-45 cables for connecting the switch to the local area network and telco lines
• Music-on-hold source with a standard mini-headphone Y-adapter (optional)
• Permanent earthing connector for grounding the device
• RJ-21 telephone cable (female on end connected to ShoreGear voice switch) for analog
port connections
• RJ-21 to RJ-11 patch panel for connecting telephones and trunk lines
• #1 Phillips screwdriver
Installation and Servicing
Installation Location Requirements
To ensure optimum operating conditions for the SG-220T1A voice switch, verify the
operating environment is adequately ventilated, free of gas or airborne particles, and
isolated from electrical noise.
Installing the ShoreGear 220T1A in a 19-inch Rack
The SG-220T1A is placed in a 19-inch rack only by mounting a ShoreGear Dual Tray into
the rack, then installing the SG-220T1A into the Tray. You can install the SG-220T1A on
the left or right side of the tray.
Refer to the Quick Install Guide for the ShoreGear Dual Tray for Tray installation
instructions and information on using the tray.
Mounting the ShoreGear Voice Switch on a Flat Surface
If you plan to mount the switch on a flat surface, first attach the provided rubber feet
to the bottom corners of the device. (You can stack up to three switches in a surface
installation.)
German: Das ShoreGear Voice-Schaltgerät auf einer ebenen
Oberfläche montieren
Wenn Sie planen, das Gerät auf einer ebenen Oberfläche zu montieren, befestigen Sie
zunächst die mitgelieferten Gummifüße an den unteren Ecken des Geräts. (Bei einer
Oberflächeninstallation können Sie bis zu drei Schaltgeräte übereinander stapeln.)
Attaching an Earthing Connector
To meet electrical safety requirements for proper grounding, you must connect a
permanent earthing protector between the ShoreGear voice switch and the wiring system
ground.
1. Connect a ground wire (#14 AWG wire or larger) to the screw on the back of the unit
and to the right of the product label.
2. Connect the other end of the ground wire to the wiring system ground.
CAUTION: Always connect the permanent earthing connector before attempting to connect
the switch to a LAN segment and telecommunication lines.
Port
German: Einen Erdungsleiter anschließen
Um den elektrischen Sicherheitsanforderungen für eine korrekte Erdung nachzukommen,
müssen Sie einen permanenten Erdungsschutz zwischen dem ShoreGear-Gerät und der
Erde des Kabelsystems installieren.
1. Schließen Sie ein Erdungskabel (Nr. 14 AWG oder größer) an die Schraube an der
RJ-21X Rückseite des Geräts an, die sich rechts neben dem Produktetikett befindet.
Telco Port
2. Schließen Sie das andere Ende des Erdungskabels an die Erde des Kabelsystems an.
VORSICHT: Schließen Sie immer zuerst den permanenten Erdungsschutz an, bevor Sie ver-
suchen, das Gerät an ein LAN-Segment und Telekommunikationsleitungen anzuschließen.
Servicing Procedures
WARNING: The SG-220T1A contains no internal field serviceable parts. Return the equipment to
ShoreTel for any required service procedures.
CAUTION: Internal fuses should be serviced only by qualified ShoreTel personnel. If internal fuses
are blown and require replacement, return the SG-220T1A to ShoreTel for service.
WARTUNGSVERFAHREN
ACHTUNG: Der SG-220T1A enthält keine internen Teile, die vor Ort gewartet werden können.
Senden Sie das Gerät an ShoreTel, falls Wartungsarbeiten erforderlich sein sollten.
VORSICHT: Interne Sicherungen dürfen nur von qualifizierten ShoreTel-Mitarbeitern gewartet
werden. Wenn interne Sicherungen ausgetauscht werden müssen, senden Sie den SG-220T1A zur
Wartung an ShoreTel.
Connections
Connecting the ShoreGear Voice Switch to the Network
Once the SG-220T1A Voice Switch is secured to a rack or surface-
mounted, you can connect it to the data network. Use an RJ-45 Ethernet
cable to connect one or both of the LAN ports to the network subnet.
While both ports can detect and respond to link status, the switch uses
only one LAN port at a time.
Powering on the ShoreGear Voice Switch
After connecting the switch to the network, power on the device by connecting it to an
AC power source.
1. Plug an AC surge protector (not provided) into a grounded AC power source.
2. Plug one end of the provided power cord into the receptacle on the back of the switch,
then plug the other end into the AC surge protector.
The power LED flashes momentarily, and remains lit.
• If LED is not lit, verify the power cord is plugged into the switch and power source.
• If the LED continues flashing, there is an internal error. Unplug the switch to power it
off, then power it back on. Refer to the "Configuring Switches" chapter in the ShoreTel
Administration Guide for information on flash patterns, or contact the ShoreTel
Support Services at http://www.shoretel.com.
The LAN ports auto-sense the network transport rate. When the network connection is
established, the network LED indicates a transport rate of 10 Mbps or 100 Mbps, and
whether the switch is receiving and transmitting data.
Optional Connections
After connecting the voice switch to the LAN, you can make optional
connections, including input from a music-on-hold source or output to
your internal paging system.
1. Connect a music-on-hold source (CD player or other audio source) to
the audio input port.
2. Connect your site' s paging system to the audio output port.
Connecting a T1 Line
After setting up the network connections and configuring the ShoreGear
220T1A Voice Switch for operations, you can connect your T1 line to
the switch.
Use an RJ-45 T1 cable to connect your T1 line to the Telco port.
Connecting Trunk and Telephone Lines
Use the provided cable retainer to connect the voice switch to the
telephone company' s punch-down block or patch panel.
1. Use a #1 Phillips screwdriver to remove the two screws on either side
of the RJ-21X port, then place the retainer on the port and re-attach
the screws.
2. Plug the Telco cable into the port, then pull the Velcro strap tightly
around the cable connector and fasten it.
3. Connect the other end of the Telco cable to the punch-down block or
patch panel.
CAUTION: To reduce risk of fire, use only No. 26 AWG or larger (e.g., 24 AWG) UL Listed
or CSA Certified Telecommunication Line Cord
VORSICHT: Um das Brandrisiko zu verringern, verwenden Sie nur Telekommunikationslei-
tungen Nr. 26 AWG oder größer (z.B. 24 AWG) mit UL- oder CSA-Zulassung
For detailed information on switch port and trunk configuration, see the "Configuring
Switches" and "Configuring Trunks" sections in the ShoreTel Administration Guide.