Bosch Professional GWS 20-230 P Original Instructions Manual page 20

Hide thumbs Also See for Professional GWS 20-230 P:
Table of Contents

Advertisement

20 | English
Angle Grinder
Grinding spindle thread
Max. thread length of grinding spindle
Restart protection
Starting current limitation
Weight according to EPTA-Procedure 01/2014
– with low-vibration auxiliary handle
– with standard auxiliary handle
Protection class
The specifications apply to a rated voltage [U] of 230 V. These specifications may vary at different voltages and in country-specific models.
Notes on mains connection requirements for GWS 22-230 P:
The appliance meets IEC 61000-3-11 requirements and is subject to conditional connection. The appliance can lead to occa-
sional voltage fluctuations under unfavorable power conditions. The impedance of this appliance is set as Z
user must make sure, that the connection point, with the impedance Z
impedance requirement: Z
 ≥ Z
actual
thority.
Noise/Vibration Information
Noise emission values determined according to
EN 60745-2-3.
Typically the A-weighted noise level of the power tool are:
93 dB(A); sound power level 104 dB(A). Uncertainty K =
3 dB.
Wear hearing protection!
Vibration total values a
(triax vector sum) and uncertainty K
h
determined according to EN 60745-2-3:
Surface grinding (roughing):
2
2
a
 = 5.5 m/s
, K = 1.5 m/s
,
h
Disc sanding:
2
2
a
 = 2.5 m/s
, K = 1.5 m/s
.
h
The vibration level given in these instructions has been
measured in accordance with a standardised measuring pro-
cedure and may be used to compare power tools. It can also
be used for a preliminary estimation of exposure to vibra-
tion.
The stated vibration level applies to the main applications of
the power tool. However, if the power tool is used for differ-
ent applications, with different application tools or poorly
maintained, the vibration level may differ. This can signific-
antly increase the exposure to vibration over the total work-
ing period.
To estimate the exposure to vibration accurately, the times
when the tool is switched off or when it is running but not ac-
tually being used should also be taken into account. This can
significantly reduce the exposure to vibration over the total
working period.
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping the hands warm,
and organising workflows correctly.
1 609 92A 87D | (25.10.2022)
GWS 22-230 P
mm
kg
kg
. If Z
is unknown, determine Z
max
max
Fitting
Fitting protective equipment
u
Note: If the grinding disc breaks during operation or the
holding fixtures on the protective guard/power tool become
damaged, the power tool must be sent to the after-sales ser-
vice immediately; see the "After-Sales Service and Applica-
tion Service" section for addresses.
Protective guard for grinding
Place the protective guard (5) on the spindle collar. Adjust
the position of the protective guard (5) to the requirements
of the operation and lock the protective guard (5) with the
locking screw (6).
u
Protective guard for cutting
u
u
The protective guard for cutting (13) is fitted in the same
way as the protective guard for grinding (5).
Extraction guard for cutting with a guide block
The extraction guard for cutting with a guide block (21) is fit-
ted in the same way as the protective guard for grinding (5).
Side handle
u
Screw the side handle (3) on the left or right of the machine
head depending on how your are working.
GWS 22-180 J
M 14
M 14
25
25
5.5
5.3
5.4
5.2
/ II
/ II
, on which the appliance shall be plugged in meets the
max
in consultation with the network supplier or supply au-
max
Pull the plug out of the socket before carrying out any
work on the power tool.
Adjust the protective guard (5) such that sparking in
the direction of the operator is prevented.
Always use the protective guard for cutting (13) when
cutting with bonded abrasives.
Provide sufficient dust extraction when cutting stone.
Do not operate your power tool without the side
handle (3).
GWS 22-230 J
M 14
25
5.5
5.4
/ II
= 0.18 Ω. The
actual
Bosch Power Tools

Advertisement

Table of Contents
loading

Table of Contents