JABSCO 37255 Series Quick Start Manual

QUIET - FLUSH
ELECTRIC TOILET CONVERSION
FEATURES
• Very quiet flush cycle - like a household toilet
• Converts all Jabsco, Par manual toilets and early
electric toilets to the new Quiet-Flush System
• Also converts Groco HC, HE & HF; Raritan PH,
Cricket, Compact & Crown; Sealand (Mansfield) 750
to 752 series and all Wilcox Crittenden toilets
• Single button flush actuator - with dual function water
level control switch
• Supplied with Par-Max 4 self-priming pump to provide
sea water or lake water to rinse the toilet bowl
• High capacity waste macerator and bowl discharge
pump
SPECIFICATIONS
PORTS PAR-MAX Pump and Toilet
Inlet 3/4" Hose Barb
Outlet 1" Hose Barb
MOTOR
Pump and Toilet meet U.S.C.G.
& SWITCH
Regulation 183.410 and ISO 8846
Marine for Ignition Pro tec tion.
WATER
1-2 Quarts (Litres)/Flush
CONSUMPTION
VARIATIONS
MODEL NO. DESCRIPTION
37255-0092* Toilet Conversion, 12 Volt EMC
37255-0094* Toilet Conversion, 24 Volt EMC
*This model is Marked and complies with EN50081-1 for suppression of
electro-magnetic interference.
OPERATION
The Quiet-Flush Toilet Conversion provides both quiet
operation and user control of water levels in the toilet
bowl. A single large pushbutton switch provides a simple
flush mode by ac ti vat ing both the rinse water supply and
the mac er a tor discharge pump si mul ta neous ly. An addi-
tional rocker switch offers independent control of the
rinse water supply and discharge pump separately so
the bowl water level can be easily raised or lowered by
the user. This pro vides a method of min i miz ing water
use, when desired, as well as a means of raising the
water level in the bowl when appropriate for user com-
fort. It also allows for complete evac u a tion of the bowl
water while un der way in rough sea conditions.
Model 37255-Series
INSTALLATION
The 37255-Series Quiet-Flush Toilet Conversion is com -
plete with a dedicated PAR-MAX 4 pump to provide either
sea or lake water to rinse the toilet bowl when flushing the
toilet. This pump is intended to be located remotely from
the toilet but will function best if the distance from the toi-
let is kept to a min i mum. Because it is self-priming, it may
be located above the vessel's waterline. It must be
installed with the Pumpgard strainer (provided with the
toilet) located somewhere in the inlet plumbing to the
pump. The toilet also includes a multi-function flush con-
trol which should be installed in a bulkhead location that
is convenient to the toilet and allows access for wiring to
run from the power source and to both the toilet dis-
charge pump and the PAR-MAX rinse water pump.
Before beginning the conversion, close all seacocks con-
nected with the toilet's plumbing system and take pre-
caution to ensure they remain closed until the con ver -
sion is complete. If the toilet being converted is an elec-
tric toilet, disconnect the electrical power to the toilet and
take precaution to ensure it is not restored until the con-
version is complete.
Disconnect both inlet and discharge hoses from the old
toilet and remove the toilet from its mounting surface.
Remove the hose connected to the back of the toilet's
china bowl and remove the china bowl and seat & lid
assembly from the old toilet base assembly. Ensure the
bottom surface of the china bowl is clean.The waste
pump can be oriented in any of the four possible mount-
ing positions that provides the best clearance from sur-
rounding obstructions but is generally best positioned so
it points to the rear of the toilet bowl. The four 6 mm
machine screws must be secured into the base to form
mounting studs to attach the china bowl. Place one star-
lock washer on each of the hex head machine screws and
a 6 mm hex nut in each of the hex shaped pockets on the
top surface of the base. From the underside of the base,
screw one machine screw into each of the nuts in the hex