Magnetic Resistance (Magnetic Influence); Shock; Caution - Seiko CREDOR 7R06 Operating Instructions Manual

Magnetic resistance (Magnetic influence)

Affected by nearby magnetism, a watch may temporarily gain or lose time or stop operating.
This watch is a magnetic resistant watch that is fully compliant with JIS level-1 standard.
Conditions of use
Keep the watch more than 5 cm away from magnetic products.
If the watch becomes magnetized and its accuracy deteriorates to an extent exceeding the specified
rate under normal use, the watch may need to be demagnetized. In this case, you will be charged
for demagnetization and accuracy readjustment even if it happens within the guarantee period.
Examples of common magnetic products that may affect watches
Smartphone, cellular phone, tablet terminal
(speaker, magnet of cover)
AC-powered Magnetic Portable radio
shaver cooking device
The reason why this watch is affected by magnetism
The built-in speed-regulating mechanism is provided with a magnet, which may be influenced by
a strong external magnetic field.

Shock

b CAUTION
This watch incorporates a complicated mechanism, comprising individual parts that exceed
the number that ordinary timepieces have.
Exercise caution so as not to subject the watch to excessive shock or vibration.
20 TO PRESERVE THE QUALITY OF YOUR WATCH
(JIS-1)
AC adapter Bag
(with magnet
buckle)
Magnetic Magnetic health
(speaker) necklace pillow
Troubleshooting
Troubles Possible causes
The mainspring has not been
The watch stops operating.
wound.
The watch has been left at a
low temperature (below 0°C).
The watch stops even though
the power reserve indicator is
The watch goes to the
not showing "0".
checkup mode when the
crown is pulled out twice within
3 seconds. (The checkup
mode is for delivery
inspection.)
The watch has been left in
extremely high or low
temperatures for a long time.
The watch temporarily loses/
gains time. The watch was brought into
close contact with a magnetic
object.
The watch was dropped, worn
while playing active sports, hit
against hard surfaces, or
exposed to strong vibrations.
When the watch starts moving,
Right after starting the watch,
it takes a little time before the
it seems that the seconds
speed-regulating unit starts
hand moves more quickly than
operating. (This is not a
usual when setting the time.
malfunction.)
This condensation temporarily
occurs due to a temperature
difference between the inside
of the watch and the outside
Blur in the display persists.
environment.
Moisture has entered the
watch.
TO PRESERVE THE QUALITY OF YOUR WATCH
Solutions
Turn the crown to wind the mainspring
and reset the time. While you are wearing
the watch or when you take it off, check
the remaining power shown by the power
reserve indicator and wind the
mainspring if necessary.
Turn the crown to wind the mainspring.
Under a low-temperature condition
(below 0°C), the watch may stop when
the power reserve indicator shows less
than one-fourth of the power reserve.
In order to return to the normal mode,
push the crown back to its normal
position, and pull it out to the second
click, and then push it back again to its
normal position. Even if the watch is left
untouched while it is in the checkup
mode, it will automatically return to the
normal mode after a few minutes.
* Wait until the watch starts moving
normally to set the time.
Return the watch to a normal temperature
so that it works accurately as usual, and
then reset the time. The watch has been
adjusted so that it works accurately when
it is worn on your wrist under a normal
temperature range between 5°C and
35°C.
Correct this condition by moving and
keeping the watch away from the
magnetic source, and reset the time. If
this action does not correct the condition,
contact the retailer from whom the watch
was purchased.
Reset the time. If the watch does not
return to its normal accuracy after
resetting the time, contact the retailer
from whom the watch was purchased.
It takes several seconds before the
speed-regulating unit starts operating.
To set the time correctly, wait for
approximately 30 seconds after the
seconds hand starts to move, and set the
time.
Condensation will clear when the
temperature difference is reduced. No
repair is needed.
Consult the retailer from whom the watch
was purchased.
21