Seav R 2224 Series Instructions

Seav R 2224 Series Instructions

Dual channel receiver

Advertisement

Quick Links

RXX 2224 D
 
UAL
CHANNEL
The RXX 2224 dual channel radio receiver allows the remote 
control   of   electric   and   electronic   devices   when   coupled   with 
one or more transmitters.
­ Mod.   RXS 2224:
­ Mod.   RES 2224: Narrow band
­ Mod.   RXH 2224: Narrow band
(   ) Product destined to countries where use is allowed
T
 D
ECHNICAL
ATA
­ Work frequency:
­ Power supply:
­ Max. consumption:
­ Op. transmitters:
­ TX codes that can be memorised (CH1 + CH2):
­ Control relay:
­ Working temperature:
­ Dimensions:
­ Capacity in open space:
­ Protection rating:
C
 
 
 CN1 T
ONNECTIONS
OF
THE
1: Power supply 12­24 VAC­DC
2: Power supply 0V
3: "Normally open" contact output CH1
4: "Normally open" contact output CH1
5: "Normally open" contact output CH2
6: "Normally open" contact output CH2
I
 
 
 
NSTALLATION
OF
THE
RECEIVER
It is very important to choose the place of installation carefully 
in  order   for   the   transmitter   and  the   receiver   to   function  well. 
Capacity is not only conditioned by the technical features of the 
device,   but   also   varies   depending   on   the   radio­electric 
conditions of the site.  The receiver has a tuned antenna.
The   antenna   must   be   positioned   where   it   can   be   seen   well 
away from metal structures.  
There must be a distance of at least 5 metres between the two 
 
RECEIVER
433.92
433.92
868.3
see model
12­24 VAC­DC
12­18­32 Bit or Rolling Code
500 Max
30 VDC 1A
­10 55°C
53x82x40mm
50­100m
 
ERMINAL
BOARD
GB
receivers if installation is to be successful.
MHz
P
 
 
MHz
OWER
SUPPLY
SELECTION
MHz
The power supply voltage can be selected by selection of the 
Jumper J1:
Jumper J1: 12/24 VAC­DC power supply selection.
Pos. 1­2 = 12 VAC­DC.
Pos. 2­3 = 24 VAC­DC (default).
5W
CH1 
 CH2 
AND
The   receiver   can   manage   the   two   channels   separately   and 
also allows to have different functioning modes:
Channel CH1: monostable  
of activation of Long Distance Programming.
IP 54
Channel CH2: by selecting Switch SW1, it is possible to 
select the following functioning modes for channel CH2 
(in long distance functioning mode it is monostable).
M
    L
ONOSTABLE
ONG
                                  
P
 M
ROGRAMMING
The programming of the radio controls to be associated is the 
Self­learning   type   and   is   performed   with  the   antenna   not 
connected  in the following way: press SEL once, the CODE 
CH1 LED, it will start to flash and at the same time sends the 
pre­selected code with the radio control to a distance of a few 
metres. When the LED remains on, programming in the CH1 
channel will be completed. To memorise a radio control code in 
channel   CH2,   perform  the   same   procedure   described  above 
and pressing the SEL key twice. 
The memorisation procedure can be repeated up to a max. of 
500   codes.   When   the   memory   is   full   by   repeating   the 
programming   operation,   the   CODE   CH1   AND   CODE   CH2 
LEDs   will  start   to flash  very  quickly,  indicating  that  no  more 
memorisations can take place.
L
 D
ONG
ISTANCE
The long distance programming of radio controls is obtained by 
selecting Dip Switch SW1 in long distance Pgm mode. In this 
way the receiver allows programming of the transmission code, 
without intervening directly on the SEL key. 
The long distance transmission code is programmed as 
follows: send a radio control code, previously­memorised in a 
channel, continuously for longer than 10 seconds. At the same 
time the receiver will enter the programming mode, as 
described below, for both channels.
1
 
FUNCTIONING
METHOD
functioning only with possibility 
 
 
   T
. 120 S
DISTANCE
PGM
EMP
( CH1 
 CH2)
AND
ODE
 P
 M
ROGRAMMING
ETHOD
      B
EC
ISTABLE
Rev. 1.0   10/03/2009

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the R 2224 Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Seav R 2224 Series

  • Page 1 RXX 2224 D     receivers if installation is to be successful. CHANNEL RECEIVER The RXX 2224 dual channel radio receiver allows the remote  control   of   electric   and   electronic   devices   when   coupled   with  one or more transmitters. ­ Mod.   RXS 2224: 433.92     ­ Mod.   RES 2224: Narrow band 433.92 OWER SUPPLY SELECTION ­ Mod.   RXH 2224: Narrow band 868.3 The power supply voltage can be selected by selection of the  (   ) Product destined to countries where use is allowed Jumper J1: Jumper J1: 12/24 VAC­DC power supply selection.  D ECHNICAL Pos. 1­2 = 12 VAC­DC.
  • Page 2   The   CODE   CH1   and   CODE   CH2   LEDs   will   flash  three times quickly and then switch­off. SEAV s.r.l. declares that the products RXH 2224 ­  RES 2224 ­ RXS 2224 receivers are   in   compliance   with   the   specifications   of   the   R&TTE  ...

This manual is also suitable for:

Rxs 2224Res 2224Rxh 2224

Table of Contents