Advertisement
Quick Links
HTV8EEMVP*1D
HTVEE-MVP Series Barrier-Free Water Coolers
24 or 25
(A) - See. Fig. 10
18, 19, 23
Fig. 1
NOTE: Non-refrigerated units do not include all
electrical and refrigeration components shown above.
Other components and rough-in are the same as
shown.
HTV8EEMVP*2D
OWNERS MANUAL
43
53
36
45, 57
39, 40
4, 17
26
4
15, 20
22
HTV8EEMVP*3D
44
30
47
28
54
54
2, 3, 5
7
PAGE 1
HTVDEEMVP*1D
8
49
6
30
21
29
56
27
16, 50, 51
13
37
46
48
27
56
55, 58
98600C (Rev. B - 10/10)
Advertisement
Related Manuals for Halsey Taylor HTVEE-MVP Series
Summary of Contents for Halsey Taylor HTVEE-MVP Series
- Page 1 HTV8EEMVP*1D HTV8EEMVP*2D HTV8EEMVP*3D HTVDEEMVP*1D OWNERS MANUAL HTVEE-MVP Series Barrier-Free Water Coolers 24 or 25 45, 57 39, 40 (A) - See. Fig. 10 4, 17 16, 50, 51 15, 20 18, 19, 23 Fig. 1 NOTE: Non-refrigerated units do not include all 55, 58 electrical and refrigeration components shown above.
- Page 2 HTV8EEMVP*1D HTV8EEMVP*2D HTV8EEMVP*3D HTVDEEMVP*1D Fig. 2 98600C (Rev. B - 10/10) PAGE 2...
- Page 3 HTV8EEMVP*1D HTV8EEMVP*2D HTV8EEMVP*3D HTVDEEMVP*1D HANGER BRACKET (Item 10) HANGER BRACKET & TRAP INSTALLATION 1) Remove the hanger bracket fastened to back of the cooler by removing one (1) screw. 2) Mount the hanger bracket as shown in Fig. 2 & Fig 3. NOTE: Hanger Bracket MUST be supported securely.
-
Page 4: Top Cover Removal
HTV8EEMVP*1D HTV8EEMVP*2D HTV8EEMVP*3D HTVDEEMVP*1D Top Cover Removal Please remove bottom cover before removing top cover. To remove top cover (Item 33), use a small screwdriver to release the snap for the top cover as shown in Fig. 5. Then pull the small tabs on each side of the top cover outward slightly and slide upward to remove. - Page 5 HTV8EEMVP*1D HTV8EEMVP*2D HTV8EEMVP*3D HTVDEEMVP*1D Removing the basin To remove the basin (Item 12), remove two screws (Item 49) on top of the basin (Shown in Fig. 7). Then remove the four screws (Item 59) located underneath the dispenser bottom (Item 41) as shown in Fig. 7. Finally pull polytube (Item 30) out of bubbler nipple (Item 38) as shown in Fig.
- Page 6 HTV8EEMVP*1D HTV8EEMVP*2D HTV8EEMVP*3D HTVDEEMVP*1D SENSOR RANGE ADJUSTMENT: (A) The electronic sensor used in this cooler is factory pre-set for a “visual” range of 36 inches (914 mm). If actual range varies greatly from this or a different setting is desired, follow the range adjustment procedure below: - Using a small tip screwdriver, locate range adjustment screw through the small hole between the sensor lenses...
- Page 7 HTV8EEMVP*1D HTV8EEMVP*2D HTV8EEMVP*3D HTVDEEMVP*1D SENSOR WITH FILTER LIFE INDICATOR: (B) The electronic sensor includes LED filter status indicators that are factory preset to monitor filter life. The sensor monitors the “ON” time of the water valve solenoid and keeps track of total time water is dispensed. There are (3) LED’s and indicates the following: Green LED (Good) indicates that the filter is operating within 0% - 80% of its life.
-
Page 8: Bottom Cover Removal
HTV8EEMVP*1D HTV8EEMVP*2D HTV8EEMVP*3D HTVDEEMVP*1D FIG. 12 See Fig. 10 21, 31, 42 Bottom Cover Removal To access the refrigeration system and plumbing connections, remove two screws (Item 55) to remove bottom cover (Item 34). 98600C (Rev. B - 10/10) PAGE 8... - Page 9 HTV8EEMVP*1D HTV8EEMVP*2D HTV8EEMVP*3D HTVDEEMVP*1D BLACK LED PCB FIG. 13 WHITE GREEN YELLOW SENSOR PURPLE OVERLOAD SOLENOID VALVE GREEN 14 (Black Jumper Wire) COMPRESSOR COLD CONTROL SMOOTH (LINE) RIBBED (NEUTRAL) MALE TERMINAL ON RELAY WHITE SHORT LEAD ON POWERCORD WIRING DIAGRAM - HTV8EE-MVP - 115V FIG.
- Page 10 HTV8EEMVP*1D HTV8EEMVP*2D HTV8EEMVP*3D HTVDEEMVP*1D PARTS LIST 220V-50Hz PARTS LIST ITEM NO. PART NO. DESCRIPTION ITEM NO. PART NO. DESCRIPTION 100322740560 Gasket - Bubbler (upper and lower) 31431C Fan Motor 100806740570 Grommet - Compressor Mtg. 36050C Relay 101516143550 Stud - Compressor Mtg. 36066C Power Cord 111411443890...