Page 1
YF60VRX22-ST 22” CORDLESS SNOW BLOWER OPERATOR’S MANUAL Our Customer Service staff is ready to provide assistance. In the case of a damaged or missing part, most replacement parts ship directly from Merotec USA in Atlanta or from one of our service partners in the US.
Page 2
Latch #2 Latch #1 Contact our Customer Care Center in Georgia for help with: You can also visit the Yard Force USA Product Assembly or Use website to download owner’s manuals, Missing Parts get product information and request Troubleshooting tech support.
Page 3
TABLE OF CONTENTS WARNING 1. For safe operation,read and understand the instruction manual. 2. To reduce the risk of electric shock, do not expose your cordless tool to water or rain. 3. Replace damaged parts immediately. Disconnect and remove the battery pack before servicing. Do not use when children or others are around.
PRODUCT SPECIFICATIONS that will protect your feet and improve your footing on slippery surfaces. • Use safety glasses – Also use safety Motor Brushless Battery Voltage Max* 60 V D.C. gloves, hearing and head protection. Battery Capacity 4.0 Ah • Do not force the snow blower –...
according to the instructions given in the WARNING: Read all safety warnings and operator’s manual. instructions. Failure to follow the warnings • Moving parts present risks – Keep your and instructions may result in electric face, hair, clothing, hands and feet away from moving parts.
larger extension cord with the female plug If liquid contacts eyes, additionally seek matching the male plug on the charger. medical help. Liquid ejected from the battery Make sure that the extension cord is in good may cause irritation or burns. electrical condition.
Page 7
11. Use only original battery packs. The use of 2. For optimum battery performance, avoid low discharge cycles by charging the battery pack result in injuries or an explosion. frequently. 3. Store the battery pack in a cool place, ideally INFORMATION ABOUT THE CHARGER AND at 59 F (15...
ADDITIONAL SAFETY process or those that exhibit other atypical symptoms (gassing, hissing, cracking, etc.) INSTRUCTIONS 12. Never fully discharge the battery pack SAFETY INSTRUCTIONS FOR WALK-BEHIND (maximum recommended depth of discharge SNOW BLOWERS is 80%) A complete discharge of the battery •...
• Hand-held operating position – Operation of Never operate the snow thrower without • the snow blower in the hand-held position is good visibility or light. Always be sure of your unsafe. • Walk; never run. snow blower is not running properly or hear •...
SAFETY SYMBOLS Keep bystanders and children a safe distance (at least 33 ft/10 m) The following table depicts and describes safety away from the work area. symbols that may appear on this product. Read, DANGER! Cutting/ understand and follow all instructions on the dismemberment hazard –...
Page 11
KNOW YOUR CORDLESS SNOW BLOWER Read the owner’s manual and safety rules carefully before operating your cordless snow blower. Compare the illustration below the actual unit in order to familiarize yourself with the location of the various controls and adjustments. Save this manual for future reference. FUNCTIONS 1.
GETTING STARTED 4. Clip the 2 chute clean-out tool clips on the side of the middle frame, and insert the chute clean-out tool in the clips (Fig. 4-5). 1. Remove the snowblower and all other items 5. Clip on the 2 cable clips on the frame, and from the box.
Page 13
Fig. 13 Cotter Pin Crank Rod Lower Chute Crank Fig. 9 Fig. 14 Upper Chute CHUTE CRANK ASSEMBLY Crank 1. Remove the cotter pin from the lower chute crank (Fig.10). Rubber Ring 2. Install the lower crank rod by inserting it into the opening at the back of the housing with holes aligned (Fig.11).
CHARGING THE BATTERY PACK NOTE: Remove the battery pack from the NOTE: charger after it has been fully charged. 1. Never allow the battery to completely NOTE: Battery should be fully charged before discharge before recharging. The battery pack should be placed on the charger NOTE: Make sure the mains voltage is the same whenever the battery pack is noticeably as the rating label which is located...
Page 15
2. While depressing the safety switch button, pull snowblower on this pivot point to move it the ON/OFF control bar toward you. Once the forward or backward. machine powers on, release the safety switch 4. Set discharge chute to face away from the button and begin operation (Fig.
Page 16
Do not over tighten Fig. 22 MAINTENANCE AND STORAGE SERVICING Service should be performed by a qualified technician. Use only genuine Yard Force parts for repair or replacement. If repairs are necessary, contact our toll-free helpline at 866-902-9690 STORAGE •...
LIFETIME LUBRICATION (MOTOR AND 2. Loosen the middle two sets of nuts and bolts to detach the worn rubber plate from the Lubrication is not necessary and may damage metal frame (Fig. 27). the unit. The snowblower is lubricated for lifetime 3.
3. Install the new scraper bar and fasten it NOTE: Heavy wet snow puts a load on belts, securely to the snowblower with the two thus requiring more frequent belt replacement. screws (Fig. 30). 4. To ins tall the new belt, lift the belt tension and roll the new belt onto the little pulley at an angle.
TROUBLESHOOTING PROBLEM POSSIBLE CAUSE SOLUTION The handle is not in The bolts are not properly seated. Make sure the bolts are correctly position. installed through the handle bars. Check to see if the hand knobs are tight. Refer to Assembling the Handle, page 12.
Yard Force. 3. If service or a warranty evaluation is requested, Yard Force will provide an RGA number that should be used in all communications with Yard Force and is required to be indicated on the product itself and on the outside of the box.
Page 21
You can submit a support request by scanning the QR code on this page, or by visiting: www.YardForceUSA.com/contact-support Scan Code to connect with Yard Force Support www.YardForceUSA.com Register your product today to maintain warranty coverage and stay up to date with information on the use, care, maintenance and service of your product.