Table of Contents
Advertisement
WARNING!
Never use a blade bolt if the insulated head is damaged, cracked,
or missing.
1. Ensure the fan is located correctly.
2. Place the spacers onto the fan ensuring the pegs have located into
the holes.
3. Place the blade onto the spacers ensuring the pegs have located
into the holes on the blade and ensuring the blade is positioned as
illustrated. [ Fig. K ]
4. Place the blade bolt through the centre hole of the blade. [ Fig. K ]
5. Tighten down clockwise by hand.
6. Hold the fan firmly and tighten the blade bolt with the spanner
provided.
3. OPERATION
DANGER!
Risk of injury!
Cut injury when the product starts accidentally.
v Wait for the blade to stop, disconnect the product from
the mains and use gloves before you adjust or transport
the product.
Handle adjustment:
NOTE:
Removal of lower handle fixing pins is not required to
adjust the handle.
Handle in forward position [ Fig. C ]:
1. Push the handle inwards from both sides.
2. Move the handle forward until it stops.
Handle in down position [ Fig. C ]:
1. Push the handle inwards from both sides.
2. Move the handle downward until it stops.
NOTE:
The handle does not rest flat on the ground.
Handle in operating position:
Adjustment is not required to move the handle to the operating position.
Simply pull down from the forward position or lift up from the down posi-
tion until the handle is in the most comfortable operating position.
To start the mower:
DANGER!
Risk of injury!
Risk of injury if the product does not stop when you release the
start levers.
v Do not bypass the safety devices or switches. For example do
not attach the start levers to the handle.
To start:
1. EU models: Connect female extension cable connector to the back
of the switchbox.
2. Form loop in mains cable and push the loop through the slot in the
switchbox. [ Fig. D ]
3. To secure, position loop over the hook and pull the cable back through
the slot. [ Fig. E ]
4. Connect plug to mains and switch on.
5. To prevent a ring being cut in your lawn and to clear any residual
grass, tilt your lawnmower slightly. [ Fig. F ]
NOTE:
The switchbox is provided with a lock-off button to
prevent accidental starting. [ Fig. H1 ]
6. Press and hold the lock-off button on the switchbox, then squeeze
one of the start / stop levers towards the upper handle. [ Fig. H ]
7. Continue to squeeze the start / stop lever towards the upper handle
and release the lockoff button.
8. When the lawnmower has reached full speed gently lower it onto the
lawn.
11250-85.960.02.indd 7
11250-85.960.02.indd 7
NOTE:
There are two start / stop levers fitted. Either one can be
used for starting the lawnmower.
IMPORTANT:
Do not use the start / stop levers intermittently.
To stop:
1. To prevent a ring being cut in your lawn and to clear any residual
grass, tilt your lawnmower slightly. [ Fig. F ]
2. Release the pressure on the start / stop lever.
How to use the mower:
1. Start mowing the edge of the lawn nearest to the power point so the
cable is laid out on the lawn you have already cut. [ Fig. J ]
2. Cut your grass twice a week during the growing season. Your lawn will
suffer if more than a third of its length is cut at one time.
CAUTION!
Do not overload your mower.
Mowing long thick grass may cause the motor speed to drop. You will
hear a change in the motor sound. If the motor speed drops, you may
overload your lawnmower which may cause damage. When mowing in
long thick grass, a first cut with the cutting height set higher will help
reduce the load. See Adjusting the Cutting Height.
4. MAINTENANCE
DANGER!
Risk of injury!
Cut injury when the product starts accidentally.
v Wait for the blade to stop, disconnect the product from the
mains and use gloves before you maintain the product.
To clean the mower [ Fig. P ]:
DANGER!
Risk of injury!
Risk of injury and risk of damage to the product.
v Do not clean the product with water or with a water jet
(in particular high-pressure water jet).
v Do not clean with chemicals including petrol or solvents.
Some can destroy critical plastic parts.
The airflow slots must always be clean.
It is very important that you keep your lawnmower clean. Grass clippings
left in any of the air intakes or under the hood could become a potential
fire hazard.
1. Remove grass from under the hood with spanner / scraper tool.
2. Using a soft brush, remove grass clippings from all air intakes.
3. Remove the blade to gain access to the fan and clean with a soft
brush.
4. Wipe over the surface of your lawnmower with a dry cloth.
5. STORAGE
To put into storage:
The product must be stored away from children.
1. Disconnect the product from the mains.
2. Clean the mower (see 4. MAINTENANCE).
3. Store the mower in a dry, enclosed and frost-free place where it is
protected from damage.
Storage positions [ Fig. S ]:
There are two kinds of storing the mower:
– Lying storage position
– Wall-mounting storage position
NOTE: When wall-mounting storage, always hang the mower from
the lower handle
(7)
cross section.
7
18.11.22 09:13
18.11.22 09:13
Advertisement
Table of Contents
