Operation - Flymo Chevron 32VC Operator's Manual

10. Never operate the machine with defective guards or shields, or without safety
devices, for example deflectors and/or grass collector, in place.
11. Switch on the motor carefully according to instructions and with feet well
away from the blade(s).
12. Do not tilt the machine when switching on the motor, except if the machine
has to be tilted for starting. In this case, do not tilt it more than absolutely
necessary and lift only the part, which is away from the operator.
13. Do not start the machine when standing in front of the discharge opening.
14. Do not put hands or feet near or under rotating parts. Keep clear of the dis-
charge opening at all times.
15. Do not transport the machine while the power source is running.
16. Stop the machine, and remove the plug from the socket. Make sure that all
moving parts have come to a complete stop
• whenever you leave the machine,
• before clearing blockages or unclogging chute,
• before checking, cleaning or working on the machine,
• after striking a foreign object. Inspect the machine for damage and make
repairs before restarting and operating the machine;
if the machine starts to vibrate abnormally (check immediately)
• inspect for damage,
• replace or repair any damaged parts,
• check for and tighten any loose parts.
Maintenance and storage
1. Keep all nuts, bolts, and screws tight to be sure
the machine is in safe working condition.
2. Check the grass collector frequently for wear or deterioration.
3. On machines with multi blade, take care as rotating one blade can cause
other blades rotate.
4. Be careful during adjustment of the machine to prevent entrapment of the
fingers between moving blades and fixed parts of the machine.
5. Always allow the machine to cool down before storing.
6. When servicing the blades be aware that, even though the power source is
switched off, the blades can still be moved.
7. Replace worn or damaged parts for safety. Use only genuine replacement
parts and accessories.
Additional safety warnings
Electrical safety
DANGER! Cardiac arrest!
This product makes an electromagnetic field while it operates.
This field may under some conditions interfere with active or
passive medical implants. To decrease the risk of conditions
that can possibly injure or kill, we recommend persons with
medical implants to speak with their physician and the medical
implant manufacturer before you operate the product.
Before use, examine the cable for signs of damage or ageing. If the cable is
found to be defective, take the product to an Authorised Service Centre and have
the cable replaced.
Do not use the product if the electric cables are damaged or worn.
Immediately disconnect from the mains if the cable is cut, or the insulation is
damaged. Do not touch the electric cable until the cable has been disconnected.
Do not repair a cut or damaged cable. Replace it with a new one.
The extension cable must be uncoiled. Coiled cables can overheat and reduce
the efficiency of your mower.
Keep the extension cable away from product, always work away from the power
point mowing up and down, never in circles.
Do not pull cable around sharp objects.
Always switch off at the mains before disconnecting any plug, cable connector or
extension cable.
Stop the engine, disconnect the mains and examine the cable for damage or
ageing before you wind the cable for storage. Do not repair a damaged cable,
replace it with
a new one. Use only genuine replacement cable.
Always wind the cable carefully, avoid kinking.
Do not carry the product by the cable.
Do not pull on the cable to disconnect any of the plugs.
Use only on AC mains supply voltage shown on the product rating label.
Our products are double insulated to EN 60335. Do not connect an earth to
any part of the product.
Check the working area for hidden cables.
Do not use for pond care or close to water.
Personal safety
DANGER! Risk of suffocation!
Small parts can be easily swallowed. There is also a risk that the
polybag can suffocate toddlers. Keep toddlers away when you
assemble the product.
Do not use in explosive atmosphere.
6
21034-85.960.01.indd 6 21034-85.960.01.indd 6
Do not operate the product when you are tired, ill or under the influence of alco-
hol, drugs or medicine or when you are exhausted.
Do not overload the mower.
Use gloves, wear slip resistant shoes and wear eye protection.
Do not use under wet conditions.
Do not use on wet grass.
Do not disassemble the product further than the delivery status.
Only start the mower with an upright standing handle.
Do not use the start levers alternately.
Use the handles carefully.
Safety Cut-Out
The engine is protected by a Safety Cut-Out which is activated when the blade
becomes jammed or if the engine is overloaded. When this occurs, stop and
disconnect the product from the mains. The Safety Cut-Out will only reset when
you release the start / stop lever. Clear any obstruction and wait for a few minutes
for the Safety Cut-Out to reset before you continue to use the product.
2. ASSEMBLY
DANGER! Risk of physical injury!
Cut injury when the blade turns or the product starts
accidentally.
v Wait for the blade to stop, disconnect the product from the
mains and use gloves before you do assembly.
The Loose Parts Pack is packaged underneath the deck.
To assemble the lower handles to the deck [ Fig. A / B ]:
1. Place the bolt (A2) through the hole in the lower handle (A1) until
the lower handle fits into the recess (A3).
2. Place the washer (B1) and the wing knob (B2) on to the bolt and
tighten the wing knob. It may take 20 – 25 urns to fully tighten on
initial assembly.
3. Repeat on the other side.
To assemble the upper handles to the lower handles [ Fig. C ]:
1. Ensure the upper handle is located correctly with the lock-off button
on the switchbox uppermost.
2. Ensure the upper handle (C1) and the lower handle (C2) are aligned
correctly.
4. Fit the bolts (C3), washers (C4) and wing knobs (C5). Tighten the wing
knob.
5. Fit the cable to the handles with the clips provided. Make sure the cable
is not trapped between the upper and lower handles.
To assemble the grassbox [ Fig. D / E / F ]:
1. Slide the grassbox tongue into the slots in the grassbox lower until it
clicks securely into position (D).
2. Push the grassbox handle into the slots in the grassbox upper until it
clicks securely into position (E).
3. Starting at the rear of the grassbox, locate the grassbox upper into the
grassbox lower by aligning the clips (F1). Ensure all clips are correctly
located (F2) before clicking into position.
4. Clip the two halves together, ensuring all clips are securely connected.

3. OPERATION

DANGER! Risk of injury!
Cut injury when the blade turns or the product starts
accidentally.
v Wait for the blade to stop, disconnect the product from
the mains and use gloves before you connect or adjust the
product.
To use the lawnmower with the grass box:
To fit fully assembled grassbox to lawnmower [ Fig. G / H ]:
1. Lift safety flap (G1).
2. Make sure the discharge chute is clean and free from debris (G2).
3. Locate fully assembled grassbox onto 2 location points (G3) at the rear
of the deck as illustrated in pic. H.
4. Locate safety flap onto the top of the grassbox. Ensure the grassbox is
securely located.
23.09.21 10:11 23.09.21 10:11