NuAire SQF Installation Manual

NuAire SQF Installation Manual

Square single high temperature fan 400 c for 2 hrs

Advertisement

Quick Links

1.0 SAFETY INFORMATION

The provision of the electrical supply and the connection of the unit to the mains must be
carried out by a qualified electrician.
Isolate from power supply before removing any covers. During installation / maintenance ensure
all covers are fitted before switching on the mains supply.
All-pole disconnection from the mains as shown in the wiring diagram must be incorporated
within the fixed wiring and shall have a minimum contact separation of 3mm in accordance with
latest edition of the wiring regulations.
This unit must be earthed.
Ducting must be securely fixed with screws to the spigot to prevent access to live parts. Duct
runs terminating close to the fan must be adequately protected by suitable guards.
If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or
similarly qualified persons in order to avoid a hazard.
Precautions must be taken to avoid the back-flow of gases into the room from the open flue of
gas or other fuel-burning appliances.
This appliance should not be used by children or persons with reduced physical, sensory or
mental capabilities or lack of experience and knowledge, unless they have been given supervision
or instruction concerning the safe use of the appliance by a person responsible for their safety.
Children shall not play with the appliance. Cleaning and user maintenance shall not be carried
out by children.

1.1 Hazard Symbols

GENERAL WARNING
Signifies a general warning regarding hazard specified by supplementary information.
ELECTRIC SHOCK
This unit must be completely electrically isolated before any panels are removed. Check
mains supply and control connections.
ROTATING PARTS
This unit contains fast moving rotational parts which may start automatically. It is the
sole responsibility of the installer to adequately guard these components.
REFER TO INSTRUCTION MANUAL
Read and understand the installation and maintenance manual before installing,
operating or maintaining this product.
Nuaire | Western Industrial Estate | Caerphilly | CF83 1NA | nuaire.co.uk
SQF
Square Single High Temperature Fan
400°C for 2 hrs
Installation Manual
01. 08. 22. Document Number 671834
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SQF and is the answer not in the manual?

Questions and answers

Summary of Contents for NuAire SQF

  • Page 1 REFER TO INSTRUCTION MANUAL Read and understand the installation and maintenance manual before installing, operating or maintaining this product. Nuaire | Western Industrial Estate | Caerphilly | CF83 1NA | nuaire.co.uk 01. 08. 22. Document Number 671834...
  • Page 2 1, 2, 3 or 4 (6 Pole Motors) 4. Control Type: No Suffix = Speed Controllable T = Two Speed Motor Control Nuaire | Western Industrial Estate | Caerphilly | CF83 1NA | nuaire.co.uk 01. 08. 22. Document Number 671834...
  • Page 3 "significant mass" accessories should form part of the comply with regulations will invalidate any warranty claim. fixed ductwork after the flexible connection. Nuaire | Western Industrial Estate | Caerphilly | CF83 1NA | nuaire.co.uk 01. 08. 22. Document Number 671834...
  • Page 4 Starting (Both Speeds), Observe Motor Plate & Connection Details Speed Motor terminal High Speed 380V 3 phase 60Hz supply 400V 3 phase 50Hz supply 460V 3 phase 60Hz supply Nuaire | Western Industrial Estate | Caerphilly | CF83 1NA | nuaire.co.uk 01. 08. 22. Document Number 671834...
  • Page 5 Failure to maintain the unit as recommended will invalidate the (grease quantity, grease quality and re-greasing frequency). warranty. The bearings must be replaced after 20,000 hours of operation. Nuaire | Western Industrial Estate | Caerphilly | CF83 1NA | nuaire.co.uk 01. 08. 22. Document Number 671834...
  • Page 6 Please call After Sales Support for further information on items not listed above. Ensure that Nuaire product is made safe from any electrical / water / refrigerant supplies before dismantling commences. This work...
  • Page 7 GENERAL INSTALLATION REQUIREMENTS The equipment referred to in this Declaration of Incorporation is supplied by Nuaire to be assembled into In addition to the particular requirements given for the individual product, the following general requirements a ventilation system which may or may not include additional components.
  • Page 8 Compatibility Regulations 2016 No. 1091. To be read in conjunction with the relevant product documentation (see 2.1) GENERAL INSTALLATION REQUIREMENTS The equipment referred to in this Declaration of Incorporation is supplied by Nuaire to be assembled into In addition to the particular requirements given for the individual product, the following general requirements should be noted.

Table of Contents