Download Print this page

MTI FREEDOM MICRO II Product Manual

Hide thumbs Also See for FREEDOM MICRO II:

Advertisement

Quick Links

CONTENTS
FREEDOM MICRO
Contents
1.
Components And Accessories
2.
Baseplate Options
3.
Speedplate™ Merchandising
4.
Speedbracket™ Merchandising
5.
SmartCable™ Merchandising
6.
RFID Commands
7.
RFID MTI Connect
8.
LED Status Indicators
9.
Dimensions
10.
FCC and ISED Statement
WARNING: MTI products contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
Proposition 65, California Health & Safety Code Section 25249.6 et seq. Visit oehha.ca.gov for more information.
www.MTIGS.com | T:800.426.6844
Product Manual for
®
Pairing
DO NOT REMOVE FROM STORE
For additional support, please reach out to our
Contact Center at 800-426-6844
FREEDOM MICRO
®
II MECHANICAL MANUAL
®
II Mechanical
MTI P/N 063-00410 rev B ©2022 MTI All Rights Reserved
2
3
5
7
10
11
12
13
15
18
1

Advertisement

loading
Need help?

Need help?

Do you have a question about the FREEDOM MICRO II and is the answer not in the manual?

Questions and answers

Summary of Contents for MTI FREEDOM MICRO II

  • Page 1 Contact Center at 800-426-6844 WARNING: MTI products contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Proposition 65, California Health & Safety Code Section 25249.6 et seq. Visit oehha.ca.gov for more information.
  • Page 2 ® II Puck Freedom Micro ® II Riser SpeedBracket™ Mounting Options VHB Mounting Through Hole Mounting Slot Mounting ® Freedom Micro II Tool SpeedPlate™ Options Phones Tablets www.MTIGS.com | T:800.426.6844 MTI P/N 063-00410 rev B ©2022 MTI All Rights Reserved...
  • Page 3 Place Micro position in desired location. Press down on the base plate for 10 seconds for full adhesive contact. Allow 24 hours for full adhesion. ADHESIVE POSITION REMOVAL Do not cut power cable. www.MTIGS.com | T:800.426.6844 MTI P/N 063-00410 rev A ©2022 MTI All Rights Reserved...
  • Page 4 Place the power cable into the slot on the bottom hole. plate, then slide it up over the slot adapter post. ® Secure the Freedom Micro II position with the knob. www.MTIGS.com | T:800.426.6844 MTI P/N 063-00410 rev B ©2022 MTI All Rights Reserved...
  • Page 5 Place the device onto the puck and rotate the device retainer towards the charge port of the phone. Use the clockwise on the puck until it locks into place. SpeedPlate™ cable retainer as alignment reference. www.MTIGS.com | T:800.426.6844 MTI P/N 063-00410 rev B ©2022 MTI All Rights Reserved...
  • Page 6 Freedom Micro II tool into the opening below the counterclockwise in relation to the tether. Lift the puck charge port on the puck. Twist the Freedom Micro II off of tether connection. tool counterclockwise to unlock the puck from the tether.
  • Page 7 Place the phone into the universal bracket. Adjust the universal bracket to fit the device snugly. Charge port of phone should face towards cable clip on SpeedBracket www.MTIGS.com | T:800.426.6844 MTI P/N 063-00410 rev B ©2022 MTI All Rights Reserved...
  • Page 8 Tighten center screw again until tight. Tighten the other Place device back onto puck. bracket security screw for additional security. www.MTIGS.com | T:800.426.6844 MTI P/N 063-00410 rev B ©2022 MTI All Rights Reserved...
  • Page 9 Grab the exposed portion of the puck with your thumb until it locks into place. and forefinger. Move the phone back and forth to checking to ensure the bracket locked in place. *click* *Back and Forth* www.MTIGS.com | T:800.426.6844 MTI P/N 063-00410 rev B ©2022 MTI All Rights Reserved...