1. Manuals
  2. Brands
  3. Alberici Manuals
  4. Cash Counter
  5. HIRA 1 ARM POS
  6. Operator's manual

Alberici HIRA 1 ARM POS Operator's Manual

Money changer
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Hira One
POS
ARM
Money Changer
VPOS
Operator's Manual
Rev. 2.00
HIRA 1
POS
ARM
Operator's manual
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the HIRA 1 ARM POS and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Alberici HIRA 1 ARM POS

Summary of Contents for Alberici HIRA 1 ARM POS

  • Page 1 Hira One Money Changer VPOS Operator’s Manual Rev. 2.00 HIRA 1 Operator’s manual...
  • Page 2 Alberici SpA shall not be held liable by the User for any damage, losses, or third-party claims arising from any uses of the manual or of the product.

  • Page 3: Table Of Contents

    CONTENTS Package content..........................4 Component names ........................4 Product description ........................5 Warning ............................5 Installation ............................ 6 Operation ............................8 System configuration ......................... 11 Messages ............................ 21 Cleaning the Note Validator....................... 24 11. Disposal of the product ......................25 12.

  • Page 4: Package Content

    Please read carefully this handbook, to obtain the most from your machine. 1. Package content The package contains: 1. the Alberici HIRA ONE Change machine 2. 2 pairs of metal keys (for Open/close lock and for Refill lock) 3. the power cable (see inside of money box) 4.

  • Page 5: Product Description

    Internet. It is recommended to check carefully that the SIM card functions properly in the area. Else, Alberici provides its B2B SIM Card, that connects automatically to the most powerful network in the area. Available functions...

  • Page 6: Installation

    5. Installation PAY ATTENTION: IT IS ESSENTIAL TO FASTEN THE MACHINE TO A SOLID WALL BY USING EXPANSION BOLTS USE OF THE WALL SLAB (code no. HR1-013A-V06) is recommended. 27,5 27,5 All measures in mm Put the Change Machine in place and fasten it to the wall by fitting expansion bolts through the rear side 4 “x”...
  • Page 7 MOUNT Prepare the tunnel for the power cable in the wall (corresponding to “Y” Hole in the slab). Fasten the slab to the wall by sturdy expansion bolts, through the 6 “X” ( 12 mm) holes. Connect the cable to its socket behind the machine, and hang the latter on the 4 “W”...

  • Page 8: Operation

    The “LANGUAGE/SEL” pushbutton allows the User to get display messages in his preferred language: default languages are Italian, English, German, French, Dutch; other languages can be loaded by using the Alberici Babbel software. “LANGUAGE” function is not available in Hira One when equipped with POS. Two operation modes are available: A...
  • Page 9 6.2.2 POS: POS payments shall only allow to obtain Tokens. If the machine is set for dispensing coins, POS operation will be automatically disabled. POS will be available only if the machine is equipped with single-coin Hopper; if the machine is equipped with multi-coin Hopper (Discriminator), the configuration menu shall make the POS option unavailable.
  • Page 10 Insert Press greenlit NITIALIZE Master or Service CCOUNTS Card/Key pushbutton Press greenlit Press greenlit OK pushbutton OK pushbutton Totals In: (*) If Card/Key is not 0,00 € compatible (i.e. its PIN is INITIALIZED! different from the PIN of the ACS reader), the Press greenlit Remove Master or warning ‘KEY NOT...

  • Page 11: System Configuration

    7. System configuration 7.1 Default setup This Money-Change machine is preset by default as follows (unless requested for different setup): Control Board Parameters Pay-out mode = AUTOMATIC Bonus = DISABLED Level sensors = DISABLED Hopper S11 Parameters € 2.00 = ENABLED Hopper AH4 discriminator [ccTalk] Preset by default to 0,50 –...
  • Page 12 7.2.1 I POS T NSTALLING THE ERMINAL Depending on the type of POS that the machine has been requested, the relevant interface with cable is provided among the accessories (find it inside the cashbox): IF for VPOS Touch Nayax IF for WORLDLINE VALINA IF for PAYTER Connect the 4p end of the POS Interface cable to the TTL1 socket of the main pcb.
  • Page 13 7.3 Menu functions 7.3.1 S URFING THE To enter the menu and navigate it, keep pressed the 3 buttons behind the display for 5 seconds. “OK” confirm selection “+” / “-“ navigate menu UP and DOWN; or, modify figures and letters MENU MAIN STRUCTURE CHANGEONE Promo...
  • Page 14 7.3.2 Show peripheral units This menu allows checking the state of the , for instance: PERIPHERAL UNITS HOPPER 1 NOTE VALIDATOR OIN ACCEPTOR EMPTY CONNECTED DISCONNECTED 7.3.3 Show accounts This menu allows to check the total and the partial values of cashed and paid amounts. SHOW RESET ACCOUNTS...
  • Page 15 7.3.5 Setting up the peripheral units and POS This menu allows to set up the denominations accepted by the note validator and by the coin acceptor, as well as the value of the coins/tokens dispensed. It also permits to set the change mode as either automatic or manual, and to enable/disable the full/void sensors of the hoppers.
  • Page 16 7.3.5.2 C OIN SELECTOR SETUP The board automatically detects the presence of the coin selector during initial check. Among the accepted coins (0.05-to-2 €), the following ones get enabled by default: 0.50 € - 1.00 € - 2.00 €. To modify this condition, press OK to get to the first option (ex. 2 €) and highlight it, then press UP or DOWN to reverse its state.
  • Page 17 Please notice the following: Master and Manager Cards can only be created using Chip Cards CH-2N01. User Cards can only be created from Standard Cards CH-2N02 or CH-2N03. Any type of Keys can only be created using Alberici branded keys: CH-1C11 - CH-1C16.
  • Page 18 Insert the Master Card/Key in the initialized ACS RFID Reader: the machine 4-digit pin code (see section 9.3.13) will be requested; enter it to get the Master Card/Key initialized. Do not remove the Card/Key during the initialization process, until the Card/Key initialized! confirmation that the Card / Key has been initialized gets displayed.
  • Page 19 7.3.5.5 GSM/GPRS When the GSM/GPRS kit is installed, it gets detected during self-configuration, and its parameters must be set up for operation. SMS functions will not be working on Hermes GPS/GSM module; remote control will then be managed only through the Argo Portal or through the Argo App. Insert Name: Name of Machine Please wait …….
  • Page 20 (*) By the buttons + and - , locate the letter/digit, and press the OK button to confirm your choice; the cursor will automatically move to the next character. There are 16 characters in the machine name, and 10 in the User Code. After confirming the last character, the name or the /code you have typed gets automatically saved.
  • Page 21 The language thus entered shall therefore appear among those selectable by default and among those of courtesy. In this regard, check the Babbel Software Manual available on the www.alberici.net website. 7.3.10 Advert message It is possible to preset an advertisement on the display.
  • Page 22 7.3.12 Manual Refill Set Up (not available in all units) Refill can take place when unit is empty or not. Allows to record the amount introduced manually. MANUAL REFILL MANUAL REFILL SET UP SET UP MANUAL REFILL MANUAL REFILL Confirm? Confirm? Enter filled Total...

  • Page 23: Messages

    8. Messages Display contrast Should the contrast between the characters and the background be not convenient, adjust it as follows: disconnect the cable from socket POWER IN/CCT of the pcb, and power up the machine; hold down the “+” and “-“ buttons of the pcb at the same time, and plug the cable into socket POWER IN/CCT;...
  • Page 24 Messages from the Note validator 8.2.1 BillyOne / OryOne Validator During operation, the amount of consecutive red flashes produced by the entry slot indicates the possible malfunctions (see chart below): no of red flashes Description Validator is open Jammed banknote Fraud attempt detected Adjust optic sensors Stacker full (OryOne Only)

  • Page 26: Cleaning The Note Validator

    9. Cleaning the Note Validator WARNING! Do switch power off before opening the machine! Manual cleaning The ability of acceptance may decrease due to the accumulation of dust and cellulose dust released by banknotes during transit, or because of residues or sprays, which may spread on the detecting sensors and on transmission parts.

  • Page 27: Disposal Of The Product

    - detailed report of the problem found and the circumstances in which it occurs. Before sending the product, please get in touch with your Dealer or with Alberici S.p.a. (+39 051 944300); very malfunctions can be fixed via a simple phone call, saving you costs and time.
  • Page 28 ATTACHMENT: Spare parts List...
  • Page 33 NOTICE Alberici S.p.A. reserves the right to change the features and the specifications to the equipment described at any time and without notice, in the pursuit of the incessant improvement of its products.
  • Page 34 Progettazione e produzione di sistemi di pagamento, accessori per videogames e macchine vending Design and manufacture of payment systems, accessories for videogames and vending machines Via Ca’ Bianca 421 Tel. + 39 051 944 300 http://www.alberici.net 40024 Castel San Pietro Fax. + 39 051 944 594 Terme (BO) – ITALY...

This manual is also suitable for:

Hira 1

Table of Contents