Related Manuals for Aprilaire S86N MU
Summary of Contents for Aprilaire S86N MU
- Page 1 Thermostats HEATING OWNER’S MANUAL Model S86N MU Multi-Stage Universal Thermostat Model S86N MUPR Multi-Stage Universal Thermostat with IAQ READ AND SAVE THESE INSTRUCTIONS...
-
Page 2: Table Of Contents
TABLE OF CONTENTS ABOUT YOUR NEW THERMOSTAT ABOUT YOUR NEW THERMOSTAT 3 Dehumidifier Control 16 THERMOSTAT FEATURES Thermostat Features 3 If Dehumidification is done... -
Page 3: Quick Reference To Controls & Display
QUICK REFERENCE TO CONTROLS & DISPLAY MAIN MENU HOME SCREEN Main Menu Mode Hold UP ARROW EQUIPMENT Schedule Main Menu STATUS Heat Blast Mode HEATING BACK Humidifier ROOM TEMPERATURE Hold Dehumidifier Schedule Ventilation SELECT (OPENS Heat Blast ROOM MENU FROM Air Cleaning TEMPERATURE HOME SCREEN) -
Page 4: Screen Saver
84° INDOOR RH% depending on the indoor temperature Indoor RH Outside (EXCEPT S86N MU) Emergency Heat: (only for heat pumps with Mode auxiliary heat) Thermostat controls auxiliary heat Heat Cool Heat pump will not operate in Em Heat mode... -
Page 5: Change Temperature Setting
CHANGE TEMPERATURE SETTING SELECT FAN SETTING (AUTO / ON / CIRCULATE) 1. From the Home screen press When the fan mode is changed during a program adjust the current temperature setting event, it remains in that mode until the next event 2. -
Page 6: Maintenance Reminders
MAINTENANCE REMINDERS INDOOR AIR QUALITY FUNCTIONS Maintenance reminders are set up by the installer to indicate when the equipment is due for service. If a maintenance reminder is displayed, call your HVAC dealer for service. They can be EVENT-BASED™ AIR CLEANING (IF INSTALLED) reset by selecting the Reset option on the reminder message or in the Reset Service Reminders option found in the Settings menu 1. -
Page 7: Humidifier Control
3. Modes (persistent) HUMIDIFIER CONTROL (S86N MUPR ONLY, IF INSTALLED) Auto: The air cleaner will run a minimum The thermostat can be of 30 minutes every hour The air cleaner Air Cleaning configured, through the will monitor the amount of time your 3 Hrs Installer set-up, to control Automatic... -
Page 8: Automatic Mode
AUTOMATIC MODE MANUAL MODE In Automatic Mode, you will receive the optimal amount In Manual Mode, it is important to anticipate drops and of humidity so that your home and its furnishings will react to increases in outdoor temperature to maintain Humidity Setting RH Settings be protected from the potentially damaging effects of... -
Page 9: Dehumidifier Control
IF DEHUMIDIFICATION IS DONE WITH THE AIR CONDITIONER DEHUMIDIFIER CONTROL (S86N MUPR ONLY, IF INSTALLED) The thermostat will cool up to 3°F beyond the cooling setpoint for dehumidification. The thermostat can be configured, through the installer NOTE: overcooling may not be sufficient to meet the dehumidification setpoint. set-up, to control dehumidification with either a whole home dehumidifier or with the air conditioner (cooling unit). -
Page 10: Fresh Air Ventilation
Ventilation has two temporary events and two FRESH AIR VENTILATION (S86N MUPR ONLY, IF INSTALLED) permanent modes that can be set 3. Events (temporary) This thermostat can be configured, through the Ventilation Installer set-up, to control fresh air ventilation 3 Hours: Ventilation will be constantly 3 Hrs based on a predetermined hourly schedule 24 Hrs... -
Page 11: Program Schedule And Holds 20
PROGRAM SCHEDULE AND HOLDS UNDERSTANDING PROGRAM SCHEDULES The daily schedule is split into four sections: SET TIME AND DATE Wake: Temperature you would prefer to wake up to Leave: Temperature when you are away from the house 1. Select Settings from the Main Menu 2. -
Page 12: Progressive Recovery
PROGRESSIVE RECOVERY HOW TO MODIFY PROGRAM SCHEDULES 1. From the Schedule option in the The Progressive Recovery feature allows Pre-Heating or Pre-Cooling PRIOR to a scheduled Main Menu, you can turn the event in order to reach the desired temperature at the start of that scheduled event EXAMPLE: schedule On or Off, and make According to TABLE 2, the Wake time is 6:00 am, the Wake heat set point is 70°F and the Sleep changes to the schedule... - Page 13 HEAT BLAST® (IF INSTALLED) 5. Adjust Leave details and/or select Heat Blast® will raise the current room temperature 3°F to 5°F based on the installer set-up, and Leave Return Sleep Next to proceed then resume normal operation Next Next Next 6.
-
Page 14: Program Schedule Holds 26
PROGRAM SCHEDULE HOLDS SETUP MENU TEMPORARY HOLD TABLE 3 – USER SYSTEM SETTINGS TABLE Press to immediately adjust the temperature when the schedule is running This will temporarily hold the Clock Set time temperature setting until the next scheduled event HEATING Date Set date... -
Page 15: Limited Warranty 28
WARRANTY REGISTRATION Visit us online at www.aprilaire.com to register your AprilAire product. If you do not have online access, please mail a postcard with your name, address, phone number, email address, product purchased, model number, date of purchase, and dealer name and address to: Research Products Corporation, P.O.