Husqvarna PW 130 Operator's Manual page 17

9. Bleed the system before you operate the product.
Refer to To bleed the system on page 17 .
To bleed the system
CAUTION:
switch is in the off (0) position before you
bleed the system.
1. Connect the product to a water source. Refer to
connect the product to a water source on page 16 .
2. Install the spray lance on the spray gun. Refer to
install the spray lance on page 15 .
3. Disengage the power trigger lockout. Refer to
engage and disengage the power trigger lockout on
page 17 .
4. Push the power trigger and keep it pushed in until
water comes out of the nozzle on the spray lance.
(Fig. 37)
To disconnect the product from the water
source
1. Turn the power switch to the off (0) position.
2. If the product is connected to the water mains, close
the valve on the water mains.
3. If the product is connected to the water mains,
disconnect the garden hose from the water mains.
(Fig. 38)
4. If the product is connected to an open water source,
remove the suction hose from the water source.
5. Push the power trigger and keep it pushed in until no
water comes out of the nozzle.
6. Disconnect the garden hose from the water inlet on
the product. (Fig. 39)
Note:
If the product is connected to an open water
source, disconnect the suction hose.
7. Push the button on the spray handle and pull out the
high-pressure hose from the spray handle. (Fig. 22)
8. Turn the power switch to the on (I) position. Let the
product operate until no water comes out of the high-
pressure hose.
9. Turn the power switch to the off (0) position.
10. Let the spray handle, the spray lance, and the
nozzles become dry before you put the product in
storage.
To engage and disengage the power
trigger lockout
• To engage the power trigger lockout, turn the power
trigger lockout clockwise until you hear a click. (Fig.
40)
• To disengage the power trigger lockout, turn the
power trigger lockout counterclockwise fully. (Fig.
41)
1839 - 006 - 21.10.2022
Make sure that the power
To
To
To start the product
1. Connect the product to a water source. Refer to
connect the product to a water source on page 16 .
2. Connect the power plug to a power source.
3. Turn the power switch to the on (I) position. (Fig. 42)
4. Disengage the power trigger lockout. Refer to
engage and disengage the power trigger lockout on
page 17 .
5. Push the power trigger on the spray handle.
To
Note:
The product stops automatically when you
release the power trigger.
To stop the product
Note:
The product stops automatically when you
release the power trigger.
1. Release the power trigger on the spray handle.
2. Engage the power trigger lockout. Refer to
engage and disengage the power trigger lockout on
page 17 .
3. Turn the power switch to the off (0) position. (Fig. 43)
4. Disconnect the power plug from the power source.
5. Disconnect the product from the water source. Refer
To disconnect the product from the water source
to
on page 17 .
Note:
Always disconnect the product from the
water source if you go away from the product for
more than 5 minutes.
To use the foam sprayer
1. Remove the foam sprayer from its holder. (Fig. 44)
2. Fill the container on the foam sprayer with cleaning
agent.
CAUTION:
agents that are recommended by
Husqvarna.
3. Push the quick connection on the foam sprayer into
the quick connection on the spray lance until it locks
in position. (Fig. 45)
Note:
The flange on the foam sprayer must align
with the groove in the spray lance.
4. Connect the product to a water source. Refer to
connect the product to a water source on page 16 .
5. Start the product. Refer to
page 17 .
To
To
To
Use only cleaning
To
To start the product on
17