Page 1
M O D E L SVL-4AB SVL-4AB SVL-4AB SPEAKER SELECTION/VOLUME CONTROL SYSTEM WITH A/B AMPLIFIER INPUTS I N S T A L L A T I O N & O P E R A T I O N G U I D E...
Additionally, you can connect two different stereo receivers to the SVL-4AB by using its A and B amplifier inputs. You don't have to worry about overloading either amplifier.
P E A K E R E L E C T I O N Features and Benefits The SVL-4AB offers a number of improvements over other speaker selector/volume controllers: Amplifier A/B Switching—The SVL-4AB provides amplifier switching for each pair of speakers. The switches are “break-before-make“...
Page 4
SVL-4AB. 100% tested, electronically and acoustically, for frequency response, distortion and power handling. Standard 17" width allows the SVL-4AB to stack neatly with other standard size components. May be used with 4, 6, or 8-ohm speaker systems.
E L E C T I O N Installation Considerations SVL-4AB Power Handling The SVL-4AB is designed for use with receivers or amplifiers having a maximum power output of 100 watts per channel at 8 ohms. Damage caused by the use of higher-power receivers or amplifiers will void the warranty.
Page 6
The actual impedance load the SVL-4AB presents to each of your receivers or amplifiers will vary, depending on how many speaker pairs are playing, and the impedance rating of each speaker.
Page 7
Using the SVL-4AB with Tube-Type Amplifiers Virtually all tube amplifiers must have a load connected at all times. If one of the amplifiers to be connected to the SVL-4AB is a tube amplifier, be sure to always have at least one pair of speakers switched on at all times.
Page 8
ON OFF CONSTANT PROTECTION Niles Audio Corporation, Miami, Florida USA O L U M E 150Ω 5 Watt Resistor Niles SVL-4AB AMPLIFIER SPEAKER 4 SPEAKER 3 SPEAKER 2 O N T R O L Y S T E M Figure 1...
Page 9
A/B switch. AMPLIFIER A CONSTANT PROTECTION ON OFF ON OFF NILES Niles Audio Corporation, Inc. Miami, Florida USA Constant Impedance Protection Switches for each amplifier. O L U M E tional 10 position designs. SPEAKER 3...
P E A K E R E L E C T I O N Installation 1. Select a convenient location for the SVL-4AB. 2. Run all the necessary wiring to the SVL-4AB. Label the wires for future reference. See (Figure 2). TUNER Receiver A...
Page 11
3. Make the connections to the SVL-4AB. The amplifier/speaker connectors on the SVL-4AB are removable. If you wish, you may remove the SVL-4AB's connectors to facilitate installation [see (Figure 3)]. Strip 3/8" of insulation from the end of each wire. Tightly twist the end of each wire until there are no frayed ends.
P E A K E R E L E C T I O N Operation The are two ways to use the SVL-4AB. You may play and "TECH TIP" adjust the volume of one pair of speakers at a time, or play multiple pairs simultaneously.
Page 13
1. Make sure both of the amplifiers are OFF and set the vol- ume controls to minimum. 2. On the right side of the SVL-4AB's front panel is a button labeled PROTECTION. This button activates the SVL-4AB's impedance correction circuitry. The circuitry assures that both of your receivers or amplifiers will see a safe operating load when playing multiple speaker pairs simultaneously.
Page 14
8. Using the appropriate volume controls on the front of the SVL-4AB, adjust the volume of the speakers to the desired lis- tening level. The volume control of your receiver or amplifier acts as the master volume for all of your speaker pairs.
A/B button. Constant Protection Switches The SVL-4AB is equipped with rear panel overrides of the protection circuits that enables you to maintain constant impedance protection regardless of the position of the front panel switch.
Need help?
Do you have a question about the SVL-4AB and is the answer not in the manual?
Questions and answers