Advertisement
Quick Links
Parts List
Control Box
Power Cable
Lifting Column
3
Foot
3
Thank you for your order!
If you have any issues with your product, please feel free to contact us via
team@effydesk.ca
For more information, please visit
https://effydesk.ca/pages/how-to-assemble-your-height-adjustable-standing-desk
Instruction Manual
or
info@effydesk.ca
Technical Data
Segment Column
Recommend Load
Height Range
Accessory List
Accessory List
Included in Executive Frame Package
Ax12
Bx8
M6X12
M6X8
Ex19
Fx2
M4X12
Rubber Pads
*2
Hangers
Included In Executive Table top Package
Mending Plates
2
*
We will help you resolve the issue as soon as possible.
3
300 lbs
Certification
240 lbs
＜
24" to 50"
Tool Required
Cx19
Dx10
or
M5X18
M6X16
Zip Ties
3mm Allen Key
Gx12
Hx6
Ix16
(included)
M6X16
M4X10
M8X10
Tape Measure
12
M5X20*
6
7
8
9
35mm/s
UL
4mm Allen Key
(included)
Screwdriver
Extension Cord
2
Side Bracket
3
Crossbar
Cable Tray
Keypad
Advertisement
Related Manuals for Effydesk L Shaped Desk
Summary of Contents for Effydesk L Shaped Desk
- Page 1 Keypad Foot Thank you for your order! If you have any issues with your product, please feel free to contact us via team@effydesk.ca info@effydesk.ca We will help you resolve the issue as soon as possible. For more information, please visit...
- Page 2 STEP 1 Separate the Crossbar ⑦ and you will find the Crossbar Rail inside. Crossbar Rail Crossbar End Crossbar End Insert one of the Crossbar Ends into the one of the Lifting Columns ③ and secure with screws. STEP 2 Repeat the same step for the other Lifting Column.
- Page 3 STEP 4 Attach the Crossbar as shown. Allen Key STEP 5 Slide the Crossbar two Rails back into the Crossbar Ends. Please make sure to fit the slots as shown below. STEP 6 Attach the Feet ④ to the bottom of the Lifting Columns. Allen Key...
- Page 4 STEP 7 STEP 8 Please note these parts are found in the Use the screws to tighten the Hangers onto table top package the Crossbar. Allen Key Screwdriver Note: The screws do not go through the Crossbar. Hangers, Allen Key and screws are found in a separate bag.
- Page 5 STEP 10 connect all the cables to the Control Box ①. Firmly secure the Crossbar with Screws (A) and Power Port Lifting Column Ports Keypad Port Allen Key Note : Use Zip Ties (D) to secure cables under the table. Slider for Control Box STEP 11 Attach the Cable Tray ⑧...
- Page 6 STEP 12 Attach the Keypad ⑨ with Screws (F) to the tabletop. Screwdriver STEP 13 Plug the cable from the Keypad into the Control Box and flip the table onto its feet. Power Port Lifting Column Ports Keypad Port Note: The Control Box is equipped with a gyro sensor so the table and the Control Box must be level in order to work properly or else it will not move up and down.
- Page 7 Before plugging in the table, make sure that: The Lifting Columns are level and set at their lowest position. All the screws are tightened to avoid the desk from becoming wobbly. Calibrate the desk by following the steps below: Please press the Down button and hold for 10-15 seconds until the table stutters and beeps. Release the button.
- Page 8 Reset the table When an error code or “RST” appears on the display, please reset the table. Unplug the power cord from the Control Box. ● Unplug the cable that connects the Keypad to the Control Box. ● Wait 30 minutes and plug all the cables back in again. ●...
- Page 9 If you have any questions, please contact us at team@effydesk.ca info@effydesk.ca www.effydesk.ca...
Need help?
Do you have a question about the L Shaped Desk and is the answer not in the manual?
Questions and answers