Sumitomo Lynx-CustomFit LYNX2-FC Installation Manual

- LYNX2-FC for 250um or 900um Tight Buffered Fiber -
ETK1123070C

For your safety operation

The Lynx-CustomFit® Splice-On Connector is designed and
manufactured to assure personal safety. Improper operation
can result in bodily injury and serious damage to this product.
Please read and observe all warnings instructions given in this
operation manual.
Wear safety glasses
!
handling optical fiber.
Never look into the end of a microscope or optical
!
cable connected to an optical output device that is
operating. Laser radiation is invisible, and direct
exposure can severely injure the human eye.
Alcohol is flammable, causes irritation and is harmful
!
if swallowed or inhaled. Keep alcohol away from
heat, sparks, skin, and avoid contact with eyes.
In the case of the work at the high place, please be
!
careful not to drop an assembling tool.

Composition

Disposable
Holder (*1)
Front
Parts
Dummy
Cap
(*1) 1 pc / 100 connectors

Recommended Program

Splicer Fiber
T-25eS SMF
MMF
T-39FH SMF
MMF
T-Q101-CA SMF
(T-71C)
MMF
SMF : G.652, G.657
MMF : MM50(OM2), MM50(OM3), MM50(OM4), MM62.5(OM1)
North Carolina (USA)
Sumitomo Electric Lightwave Corp.
78 Alexander Drive, P.O. Box 13445, RTP, NC 27709
TEL +1-919-541-8100
http://www.sumitomoelectric.com/
Copyright © 2011 Sumitomo Electric Industries, LTD.
Lynx-CustomFit® Splice-On Connector Ver. 2
to protect your eyes when
Rear
Stopper
Boot
Protection Sleeve
and Spring
Ferrule
Subassembly
Splicing Program Heater Program
SM1: SMF1C Lynx
or FPS (60mm)
MM1: MMF1C
LYNX-SM Lynx
or FPS (60mm)
LYNX-MM
Standard SMF Lynx
or 60mm 0.9
MMF 50&62.5
London (UK)
Sumitomo Electric Europe Ltd.
220 Centennial Avenue, Elstree, Herts. WD6 3SL, UK
TEL +44 (0)20-8953-8118
http://www.sumielectric.com/
Installation Manual
1. Improper assembly will result in a loss of performance.
Please read instructions
and the operation manual of the fusion splicer.
2. Never touch the fiber of the
in the factory.
3. The product is sensitive to dirt or dust. Do not take out
any parts from the package
4. The characteristic will be influenced by the fiber
cleaved surface condition. Please use a cleaver which
has a good cleaving characteristic.
5. Do not remove the dust cap
been completely assembled
high insertion loss due to them.
Either one holder is required.
for 900um tight buffer
Furcation
LYNX2-UML-S
Tube
Below equipment or tool are examples.
Fusion Splicer
T-Q101-CA(71C), etc.
Holder Type
Please perform Arc test prior to the splicing operation.
(See the operation manual of the splicer.)
*Fiber for testing is not included in the kit.
Please check fiber type inside the field fiber.

Precautions

given in this operation manual
stub. It has been inspected
until it is to be
until the connector has
in order not to cause an

Assembling Tools

Holder (Fiber Side)
for 250um fiber
FHS-09 FHS-025
Fiber Cleaver Jacket remover
FC-6S-C, etc.
Cleave length: 10mm
Yokohama (Japan)
Sumitomo Electric Industries, Ltd.
(Lightwave Network Products Division)
1, Taya-cho, Sakae-ku, Yokohama 244-8588, Japan
TEL +81-45- 853-7223, http://global-sei.com/fttx/
used.
LYNX2-S-LB5
JR-M03, etc.