Sumitomo Lynx-CustomFit LYNX2-MPO Installation Manual

- - LYNX2 LYNX2- - MPO
ETK1123092D

For your safety operation

The Lynx-CustomFit® Splice-On Connector is designed and
manufactured to assure personal safety. Improper operation
can result in bodily injury and serious damage to this product.
Please read and observe all warnings instructions given in this
operation manual.
Wear safety glasses to protect your eyes when
!
handling optical fiber.
Never look into the end of a microscope or optical
!
cable connected to an optical output device that is
operating. Laser radiation is invisible, and direct
exposure can severely injure the human eye.
Alcohol is flammable, causes irritation and is harmful
!
if swallowed or inhaled. Keep alcohol away from
heat, sparks, skin, and avoid contact with eyes.
In the case of the work at the high place, please be
!
careful not to drop an assembling tool.
Composition
Disposable Disposable
Holder (*1)
Front
Housing
w/Spring
Dust Cap
Polish Surface and Housing Color
SM Low Loss SM Std. Loss MM62.5 OM1 MM50 OM2 MM5010GOM3
8 degree Polish
Yellow Green
North Carolina (USA)
Sumitomo Electric Lightwave Corp.
78 Alexander Drive, P.O. Box 13445, RTP, NC 27709
TEL +1-919-541-8100
http://www.sumitomoelectric.com/
Copyright © 2011 Sumitomo Electric Industries, LTD.
Lynx Lynx- - CustomFit CustomFit® ® Splice
MPO for for Round Round Cord
Rear Parts Rear Parts
Rear Boot
Stopper
Protection
Sleeve
MT STUB
Dummy Cap
w/ Tether
(*1) 1 pc / 100 connectors
Flat Polish
Beige Black
London (UK)
Sumitomo Electric Europe Ltd.
220 Centennial Avenue, Elstree, Herts. WD6 3SL, UK
TEL +44 (0)20-8953-8118
http://www.sumielectric.com/
Splice- - On On Connector Connector Ver. 2
Cord with with 12 or 8 12 or 8 Individual
Installation Manual Installation Manual
1. Improper assembly will result in a loss of performance.
Please read instructions given in this operation manual
and the operation manual of the fusion splicer.
2. Never touch the fiber of the stub. It has been inspected
in the factory.
3. The product is sensitive to dirt or dust. Do not take out
any parts from the package until it is to be used.
4. The characteristic will be influenced by the fiber
cleaved surface condition. Please use a cleaver which
has a good cleaving characteristic.
5. Do not remove the dust cap until the connector has
been completely assembled in order not to cause an
high insertion loss due to them.
Below equipments and tools are required.
Fusion Splicer
Type-Q101-M12
Furcation Furcation
(T-71M12) (T-71M12)
Tube
Fiber Alignment Tool
Spiral
FA-03
Tube
Splicer
Type-Q101-M12
(T-71M12)
SMF : G.652, G.657
MMF : MM50(OM2), MM50(OM3), MM50(OM4), MM62.5(OM1)
Aqua
Please perform Arc test prior to the splicing operation.
(See the operation manual of the splicer.)
*Ribbon fiber for testing is included in the connector kit.
Please check fiber type inside the field fiber.
Ver. 2
Individual Fibers Fibers - -

Precautions

Assembling Tools

Jacket
Fiber Cleaver
Remover
FC-6RM etc.
JR-6 JR-6
Cord Tool
LYNX2-CORDTOOL-
2&3
Recommended Program
Fiber Splicing Program
SMF 12c SM12c
SMF 8c SM8c
MMF 12c MM12c
MMF 8c MM8c
Yokohama (Japan)
Sumitomo Electric Industries, Ltd.
(Lightwave Network Products Division)
1, Taya-cho, Sakae-ku, Yokohama 244-8588, Japan
TEL +81-45- 853-7223, http://global-sei.com/fttx/
Fiber Holder Fiber Holder
FHM-12 FHM-8
(For 12c Fiber) (For 8c Fiber)
(For 12c Fiber) (For 8c Fiber)
Kevlar Cutter
Heater Program
Lynx MPO