General; Location Of Controls; Connections - Sony CDX-GT170S Service Manual

• LOCATION OF CONTROL
Location of controls and basic operations
Main unit
1 2 3 4
OFF
PUSH SELECT
EQ3
SOURCE
SEEK SEEK
MODE
DSPL
BTM 1
9 q; qa qs qd qf
Card remote commander
RM-X151 (CDX-GT370S/GT370/
GT270S/GT270 only)
wa
1
OFF ATT
ws
4
SOURCE SEL MODE
qs
qk
+
wd
–
ql wf
DSPL SCRL
1 2 3
wg
4 5 6
+
w;
VOL
–
6

• CONNECTIONS

A
*
AUDIO OUT REAR
* AUDIO OUT SUB/REAR
*
AUDIO OUT REAR
* AUDIO OUT SUB/REAR
B
CDX-GT370S/GT370
BUS AUDIO IN
BUS CONTROL IN
SECTION 2

GENERAL

5 6 7 8
AUX
REP SHUF PAUSE
2 3 4 5 6
qg qh qj
This section contains instructions on the location
of controls and basic operations.
For details, see the respective pages.
For optional device (CD/MD changer, etc.,)
operation, see "Using optional equipment" on
page 10. The corresponding buttons on the card
remote commander control the same functions as
those on the unit.
A OFF button
To power off; stop the source.
B EQ3 (equalizer) button page 9
To select an equalizer type (XPLOD,
VOCAL, EDGE, CRUISE, SPACE,
GRAVITY, CUSTOM or OFF).
C Volume control dial/select button
page 9
To adjust volume (rotate); select setup items
(press and rotate).
D SOURCE button
To power on; change the source* (Radio/CD/
AUX).
E Disc slot
Insert the disc (label side up), playback
starts.
F Display window
G AUX input jack page 10
To connect a portable audio device.
H Z (eject) button
To eject the disc.
I (front panel release) button page 5
CDX-GT170/GT170S/GT270/GT270S
J DSPL (display)/SCRL (scroll) button
(CDX-GT370S/GT370/GT270S/GT270)
page 8
To change display items (press); scroll the
display item (press and hold).
DSPL (display) button (CDX-GT170S/
GT170) page 8
To change display items.
K SEEK –/+ buttons
CD:
To skip tracks (press); skip tracks
continuously (press, then press again within
about 1 second and hold); reverse/fast-
forward a track (press and hold).
Radio:
To tune in stations automatically (press); find
a station manually (press and hold).
L MODE button page 8
To select the radio band (FM/MW/SW)*.
M BTM button page 8
To start the BTM function (press and hold).
N RESET button (located behind the front
panel) (CDX-GT370S/GT370 only)
page 5
O Frequency select switch (located on the
bottom of the unit)
See "Frequency select switch" in the
supplied installation/connections manual.
P Number buttons
CD:
(1)/(2): ALBUM –/+ (during MP3/WMA
playback) (CDX-GT370S/GT370/
GT270S/GT270)
To skip albums (press); skip albums
continuously (press and hold).
(3): REP page 8
(4): SHUF page 8
(6): PAUSE
To pause playback of a CD on this unit.
To cancel, press again.
Radio:
To receive stored stations (press); store
stations (press and hold).
Q Receptor for the card remote
commander (CDX-GT370S/GT370/
GT270S/GT270 only)
Connection example
Notes (2- A )
• Be sure to connect the ground (earth) lead before connecting
the amplifi er.
• The alarm will only sound if the built-in amplifi er is used.
Ejemplo de conexiones
Notas (2- A )
• Asegúrese de conectar primero el cable de conexión a masa
antes de realizar la conexión del amplifi cador.
• La alarma sonará únicamente si se utiliza el amplifi cador
incorporado.
This section is extracted
from instruction manual.
The following buttons on the card remote
commander have also different buttons/functions
from the unit. Remove the insulation film before
use (page 5) (CDX-GT370S/GT370/GT270S/
GT270 only).
qk < (.)/, (>) buttons
To control CD/radio, the same as (SEEK)
–/+ on the unit.
Setup, sound setting, etc., can be operated by
< ,.
ql DSPL (display) button
To change display items.
w; VOL (volume) +/– button
To adjust volume.
wa ATT (attenuate) button
To attenuate the sound. To cancel, press
again.
ws SEL (select) button
The same as the select button on the unit.
wd M (+)/m (–) buttons
To control CD, the same as (1)/(2)
(ALBUM –/+) on the unit.
Setup, sound setting, etc., can be operated by
M m.
wf SCRL (scroll) button
To scroll the display item.
wg Number buttons
To receive stored stations (press); store
stations (press and hold).
* In the case of a CD/MD changer being connected;
when (SOURCE) is pressed, the connected device
("MD") will appear in the display, depending on
which device is connected. Furthermore, if (MODE)
is pressed, you can switch the changer (CDX-
GT370S/GT370 only).
Note
If the unit is turned off and the display disappears, it
cannot be operated with the card remote commander
unless (SOURCE) on the unit is pressed, or a disc is
inserted to activate the unit first.
7
5