Related Manuals for Texecom Premier 412 Premier 816 Premier 832
Summary of Contents for Texecom Premier 412 Premier 816 Premier 832
- Page 1 THANK YOU FOR VOTING TEXECOM INSTALLATION MANUAL Security Control Panels with Integrated Communicator INS159-9...
-
Page 2: Table Of Contents
Contents Premier 412/816/832 Installation Manual Contents Viewing Numeric Data (LED Keypads)........22 System Overview........4 Programming Text (LCD Only) ...........22 Program Menus ..............23 System Architecture............4 Programming Zones ............24 Control Panels..............4 All Zone Options !" ........25 Remote Keypads .............. 4 !! ........25 Zone Type Zone Expansion Modules .......... - Page 3 Premier 412/816/832 Installation Manual Contents ('-# ....59 UDL Passcode System Overview Download Dial Attempts ('-$ ....59 Ring Count ('-% ....59 ('-& ....59 Com1 Device Type ComIP Address & Port ('-' ....59 Installation ('-( ....59 ComIP Gateway Address ComIP Subnet Mask ('-) ....59 Programming Reporting Codes........60 Control Panel PCB Layout...
-
Page 4: System Overview
System Overview Premier 412/816/832 Installation Manual 1. System Overview System Architecture 6 Remote Keypads (max) 1 Output 1 Output (100mA) (100mA) 2 EOL Zones 2 EOL Zones 2 EOL Zones ( RKP16 Plus Zones Premier 832 Alarm Armed Premier 832 Power Power Alarm... -
Page 5: Zone Expansion Modules
• Speaker driver output (Premier LCDL Only). Radio Receiver Module Premier LCDLP The control panel will accept either the Texecom RadioPlus • Premier LCDL keypad with built-in proximity tag reader receiver module and radio devices or the Inovonics EE4000 radio receiver and ES1200 series devices. The receiver... -
Page 6: Installation
Installation Premier 412/816/832 Installation Manual 2. Installation Installation Sequence Control Panel Before attempting to install the alarm system, read this Mounting section. Once you have an overall understanding of the Mount the control panel on a flat, plumb wall using at least installation sequence, carefully work through each step. -
Page 7: Control Panel Pcb Layout
Failure to fit an earth cable may prevent proper F2 (1 Amp). operation of the system and will invalidate the Texecom warranty and product approvals. 7: Zone Inputs 1 to 8 These terminals provide the connections to the zone inputs. -
Page 8: Connecting Devices To The Data Bus
Installation Premier 412/816/832 Installation Manual 11: Communication Port 23: Electronic Fuse Fault Indicator LEDs The serial communication port is used for connecting to a Electronic fuses F2-F4 have red indicator LEDs, which light printer or PC for local downloading. up when the relevant fuse is open circuit (fault). 12: Load Defaults 24: Battery Kick Start Pins Short between the centre and either of the outer pins during... -
Page 9: Overcoming Voltage Drop
Premier 412/816/832 Installation Manual Installation Installing a Power Supply The table below shows maximum cable runs when one keypad or expander is installed using standard 7/0.2 alarm When a power supply is installed, the 0V connections on the cable with various loads: power supply must be connected through to 0V on the control panel and the +12V connection between the control Configuration... -
Page 10: Installing Remote Keypads
Installation Premier 412/816/832 Installation Manual Address DIL Switch Installing Remote Keypads Tamper Switch & Piezo Sounder Keypad Layouts Data Bus Connections Programmable Zones 1 and 2 Speaker Output (Premier LCDL/LCDLP Only) Programmable Output Remote Keypad Connections The remote keypad is connected to the data bus terminals located at the bottom left hand side of the PCB. -
Page 11: Keypad Speaker Output (Lcdl/Lcdlp Only)
Premier 412/816/832 Installation Manual Installation Keypad Speaker Output (LCDL/LCDLP Only) Data Bus Connections The Premier LCDL and LCDLP keypads has an output that Auxiliary 12V & can be used for driving up to one 8Ω or two 16Ω Programmable Zone Inputs loudspeakers (see page 17 for wiring details). -
Page 12: Zone Expander Outputs
Installation Premier 412/816/832 Installation Manual Zone Expander Outputs The table below shows the zone allocation when the module The Zone Expander module has two programmable outputs, is installed: which can be used to drive auxiliary devices such as relays, Panel Panel Zones Expander Zones LED’s, smoke detectors etc. -
Page 13: Zone Connections
Premier 412/816/832 Installation Manual Installation Normally Closed Zone Connections Use this wiring configuration when connecting normally closed detection devices to the zone. Ensure that the zone Each zone on the system is fully programmable to allow for is programmed for Normally Closed operation (see page maximum flexibility (see page 24 for Zone Programming 26). -
Page 14: Single Eol - N/C & N/O (Burglary)
Installation Premier 412/816/832 Installation Manual Single EOL - N/C & N/O (Burglary) Single EOL - N/O (Fire) Use this wiring configuration when connecting a mixture of Use this wiring configuration when connecting a 4-wire normally closed and normally open detection devices to the smoke detector to the zone. -
Page 15: Single Eol - N/C
Premier 412/816/832 Installation Manual Installation Single EOL - N/C Double EOL Use this wiring configuration when connecting just normally Use this wiring configuration when connecting detection closed detection devices to the zone. Ensure that the zone devices to a zone that requires alarm/tamper monitoring. is programmed for Single EOL - N/C operation (see page Ensure that the zone is programmed for Double EOL 26). -
Page 16: Double Pole
Ensure Triple EOL that the zone is programmed for Double EOL operation (see This wiring option is designed to be used with Texecom page 26). The zone must be wired as follows: detectors that support Triple EOL (T-EOL) wiring. Ensure... -
Page 17: 2-Wire Smoke Detector
When configured as speaker operation the output can be operation of the system and will invalidate the used for driving 8 or 16 Ohm loud speakers as shown: Texecom warranty and product approvals. 8 Ohm Speaker 8 Ohm Speaker 8 Ohm Speaker The Siren/Spk output must be enabled for speaker driver (see page 35 for details). -
Page 18: Panel Outputs 1 - 8
Installation Premier 412/816/832 Installation Manual Panel Outputs 1 - 8 The control panel has eight programmable outputs, which can be used to drive auxiliary devices such as relays, LED’s, smoke detectors etc. The table below shows the electrical characteristics for each output: Supervised Max Current Type... -
Page 19: Commissioning & Troubleshooting
Premier 412/816/832 Installation Manual Commissioning & Troubleshooting 3. Commissioning & Troubleshooting Commissioning Troubleshooting Once ALL connections have been made to the control panel Power Faults and power is ready to be applied, you should read this section before continuing. No Power to Unit (mains only) •... -
Page 20: Panel Outputs
Commissioning & Troubleshooting Premier 412/816/832 Installation Manual • Keypad Does Not Generate Alarm Tones etc. If the battery presence check is enabled the system will • Each keypad can be configured so that the alarm, entry, check the battery every 30 seconds. If the system does exit, chime tones etc.
Need help?
Do you have a question about the Premier 412 Premier 816 Premier 832 and is the answer not in the manual?
Questions and answers