Toshiba RBC-ASCU11-E Reference Manual page 11

For a full list of "DN Codes" please refer to the service manual for the installed equipment or to one of the
ITEM DESCRIPTION
03 Network address
06 Stratification control
0d Auto mode
0E SHRMi only
0F Heat Mode
10 Indoor unit model
11 Indoor unit capacity
12 System number
13 Indoor unit number
14 Group master/slave
16 Indoor Fan
1E Dead band - auto
1F Max. Setting
20 Min. Setting
21 Max. Setting
22 Min. Setting
23 Max. Setting
24 Min. Setting
25 Max. Setting
26 Min. Setting
28 Auto restart
2d Modes available
103 Remote Controller
1FC IDU
Some useful DN codes.
"CDL Pocket Handbooks"
When under network control.
Increases effective return air temperature setting in heating mode (0 to 10K)
Enable or disable Auto mode
Used when multiple indoor units are served via a single FS box
Enable or disable Heat Mode
Must be set when replacing indoor printed circuit board
0000 will generate a (L09) fault
DI/SDI indoor and outdoor units are automatically addressed, this
value may be set manually but it must be done via the wired
controller – on an individual basis. Settings are 0001 to 0030
Indoor units connected to a common outdoor unit (e.g., twinned
indoor units) will have the same system number - settings are 0001
to 0064. Automatically allocated – but may be manually overridden.
Allows selection of master indoor unit within group.
Automatically allocated but may be manually overridden.
Indoor fan speed selection. Binary addition.
Changeover sensitivity in automatic mode.
Cooling mode maximum temperature setting (18 – 29
Cooling mode minimum temperature setting (18 – 29
Heating mode maximum temperature setting (18 – 29
Heating mode minimum temperature setting (18 – 29
Dry mode maximum temperature setting (18 – 29
Dry mode minimum temperature setting (18 – 29
Auto mode maximum temperature setting (18 – 29
Auto mode minimum temperature setting (18 – 29
Enable or disable
Binary addition of modes available.
VRF IDU "Up" series. Local remote controller used or not used
"U" series IDU Terminating resistance
VALUE
00Un / 0099: Unset
0001 to 0064 available
0000 to 0010
0000 = available
0000 = normal 0001= multiple units
0000 = available
0000: 1-way cassette (s models)
0001: 4-way cassette
0002: 2-way cassette
0003: 1-way cassette (y models)
0004: duct (standard)
0005: slim duct
0006: duct (high static)
0007: ceiling
0008: hi wall
0010: console
0011: concealed floor
0014: 4-way compact cassette (600 x 600)
0013: tall cabinet
0016: fresh air intake
0050: air to air heat exchanger
0004
0001
0003
0005
0006
0007
0009
0011
0 0 0 1 = 150m
0 0 0 2 = 250m
0 0 0 3 = 350m
0 0 0 4 = 500m
0 0 0 5 = 650m
0001: outdoor unit 1
0002: outdoor unit 2
0001: indoor unit 1
0002: indoor unit 2
0000: single indoor unit 0001: group
master 0002: group slave
0015 = all speeds available
1 = auto; 2 = low; 4 = medium; 8 = high
(1 to 10 k adjustable) 0000: 0 K
o
C) 0018 = 18
o
C) 0018 = 18
o
C) 0018 = 18
o
C)
0018 = 18
o
C)
0018 = 18
o
C)
0018 = 18
o
C)
0018 = 18
o
C)
0018 = 18
0000: disabled
0015= all modes
1 = fan;
0000: Use
0000: Off
0001 = unavailable
0001 = unavailable
M M R A V M M R A V
=005* - 0012 =027* 80*
=007* - 0013 =030* -
=009* 30* 0015 =036* 110*
=012* - 0017 =048* 140*
- 40* 0018 =056* 160*
=015* - 0021 =072* 224*
=018* 56* 0023 =096* 280*
=024* - - - -
Air to air heat exchanger Type
3 3
/h 0 0 0 6 = 800m /h
3 3
/h 0 0 0 7 = 1000m /h
3 3
/h 0 0 0 8 = 1500m /h
3 3
/h 0 0 0 9 = 2000m /h
3
/h
0010: 10 K
o o o
C 0020 = 20 C 0029 = 29 C
o o o
C 0020 = 20 C 0029 = 29 C
o o o
C 0020 = 20 C 0029 = 29 C
o o o
C 0020 = 20 C 0029 = 29 C
o o o
C 0020 = 20 C 0029 = 29 C
o o o
C 0020 = 20 C 0029 = 29 C
o o o
C 0020 = 20 C 0029 = 29 C
o o o
C 0020 = 20 C 0029 = 29 C
0001: enabled
2 = cool; 4 = dry 8 = heat
0001: Do not use
0001: On
DEFAULT
00Un/ 0099
o
0002; +2 C
Floor type
0000; 0ºC
0000 except
SMMSe/u
0000
0000
00Un/ 0099
00Un/0099
ooUn/0099
0015
except high static
0008
0003
o
29 C
o
18 C
o
29 C
o
18 C
o
29 C
o
18 C
o
29 C
o
18 C
0000
0015
0000
0000