Why is my Toshiba WH-H1JE2 remote control not working?

Your remote control may not be working due to several reasons:The air conditioner is not working or a power failure has occurred.The power switch of the air conditioner is not turned on.The air conditioner is in an ON timer operation.The batteries of the remote controller have been exhausted.The LEDs on the signal receiving part are not in a normal state or the operation mode is not correct.Something is blocking signals between the remote controller and the signal receiving part of the indoor unit.Rapid start-type or inverter-type fluorescent lights may disturb the signal reception.The remote controller is installed in a place where its signals do not reach the indoor unit.

My Toshiba WH-H1JE2 remote control is not working even with new batteries, what should I do?

If your remote control is not working even with new batteries, consider the following:Check if the air conditioner is not working or a power failure has occurred.Ensure the power switch of the air conditioner is turned on.Verify if the air conditioner is in the ON timer operation.Check if the LEDs on the signal receiving part are not in a normal state or the operation mode is incorrect.Make sure there are no obstructions blocking signals between the remote controller and the indoor unit's signal receiving part.Be aware that rapid start-type or inverter-type fluorescent lights may disturb signal reception.Ensure the remote controller is not installed in a place where its signals do not reach the indoor unit.

How do I reset my Toshiba WH-H1JE2 remote control?

To reset your remote control, push the RESET button with a fine-tipped tool. This button is used after batteries are replaced or the slide switch is switched.

How do I pair my Toshiba WH-H1JE2 remote control with an air conditioner?

To pair your remote control with an air conditioner, you need to match the address setting on the remote with the address switch setting in the signal receiving part of the indoor unit. Up to 6 indoor units can be controlled independently this way.Push the ADR button on the remote control for at least 4 seconds. "Address" will light up on the display, and the current address will flash.Each time you push the ADR button, addresses will change cyclically (ALL → 1 → 2 → 3...→ 6 → ALL). Select an address that matches the address switch setting in the signal receiving part of the indoor unit to be controlled.Push the SET button. The flashing address will change to lighting and be displayed for 5 seconds. If this address matches the address switch setting in the signal receiving part, the buzzer will sound. For details on the address switch setting in the signal receiving part, contact the dealer from whom you purchased the air conditioner. For more information, see page 13 of the manual.

How do I open the battery compartment of the Toshiba WH-H1JE2 remote control?

To open the battery compartment, slide the cover downward while holding both sides of the cover.

How do I switch between different operating modes (e.g., cool, heat, fan) using the Toshiba WH-H1JE2 remote?

To switch between different operating modes, push the Mode select button (labeled with a symbol that looks like a cycle arrow). You can select Auto, Heat, Dry, Cool, or Fan by pushing this button.

What do the error codes displayed on my Toshiba WH-H1JE2 remote control mean?

When a trouble occurs, a check code is displayed in the Timer time display area on your remote. Additionally, if the LEDs on the signal receiving part flash, it indicates an issue. The meaning of the flashing LEDs depends on the pattern:Communication error between the signal receiving part and indoor unit, or address setup error.Communication error between the indoor unit and outdoor unit.The protective device of the indoor unit is activated.The protective device of the outdoor unit is activated.Temperature sensor error.The compressor of the outdoor unit is protected.The air conditioner is performing a test run. If any of these problems remain, it is advised to stop the operation, turn off the power, and notify the dealer with the model name and details of the error.

How do I set or cancel a timer function on the Toshiba WH-H1JE2 remote control?

To set or cancel a timer function:Setting an OFF timer (to stop operation): Push the Timer button once. The timer symbol and time will flash on the display. Set the desired time using the TIME ▲ or TIME ▼ buttons. The setup time increases or decreases by 0.5 hours, with a maximum of 72.0 hours and a minimum of 0.5 hours. Push the Timer button again. The timer symbol and time will stop flashing. Setting a repeat OFF timer (to stop operation repeatedly): Push the Timer button twice. The timer symbol and time will flash on the display. Set the desired time using the TIME ▲ or TIME ▼ buttons. Push the Timer button again. The timer symbol and time will stop flashing. Setting an ON timer (to start operation): Push the Timer button three times. The timer symbol and time will flash on the display. Set the desired time using the TIME ▲ or TIME ▼ buttons. Push the Timer button again. The operation mode will disappear, and the timer symbol and time will stop flashing. Canceling a timer operation: Push the Timer button. The timer display will disappear. After setting the timer, ensure the remote controller is placed where its signals can reach the signal receiver on the indoor unit. For more information, see page 9 of the manual.

Why is the display screen on my Toshiba WH-H1JE2 remote control blank or dim?

The display screen on your remote control may be blank or dim because the batteries are exhausted. You should replace the batteries. For more information, see page 11 of the manual.

How do I use the basic functions of the Toshiba WH-H1JE2 remote control?

To use the basic functions of the remote control:Start/Stop Operation: Push the Start/Stop button to alternately start and stop the air conditioner.Select Operation Mode: Push the Mode select button to choose between Auto, Heat, Dry, Cool, or Fan modes.Adjust Fan Speed: Push the Fan speed button to select the desired fan speed.Set Temperature: Push the Temperature set buttons (▲ or ▼) to adjust the room temperature.Adjust Air Direction: Push the Swing/air direction button to set or start swinging the air direction.Set Timer: Push the Time setup button for timer settings.

What type of batteries does the Toshiba WH-H1JE2 remote control require?

The Toshiba WH-H1JE2 remote control requires two AAA alkaline batteries.

What is the effective operating range of the Toshiba WH-H1JE2 remote control?

The standard signal receivable distance from the signal receiving part of the indoor unit is approximately 7 meters. This distance may vary depending on battery capacity and other conditions. For more information, see page 12 of the manual.

Toshiba WH-H1JE2 Owner's Manual

Remote controller for air conditioner (split type)

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

REMOTE CONTROLLER FOR AIR CONDITIONER (SPLIT TYPE)

Owner's Manual

Remote Controller

Model name:

Wireless Remote Controller Kit

RBC-AX31U(W)-E

RBC-AX31U(WS)-E

Generic model name

RBC-AX31U(W)-E

RBC-AX31U(WS)-E

Wireless remote controller

(WH-H1JE2)

Wireless remote controller

and signal receiving part

WH-H1JE2

(Wireless remote controller

model name)

Signal receiving

part

Owner's Manual

Remote controller for air

conditioner

(Split type)

Manuel du proprietaire

Télécommande pour climatiseur

(Type split)

Betriebsanleitung

Fernbedienung für klimagerät

(Split-typ)

Manuale del proprietario

Telecomando per condizionatore

d'aria

(Tipo split)

Manual del propietario

Control remoto para aire

acondicionado

(Tipo split)

Manual do utilizador

Controlador remoto para ar

condicionado

(Tipo split)

Gebruiksaanwijzing

Afstandsbediening voor

airconditoner

(Gesplitst type)

Εγχειρίδιο χρήσης

ΤηλεΧειριστηριο για κλιματιστικο

(

)

ΤυΠου split

Руководство пользователя

Пульт дистанционного упРавлениЯ длЯ

кондиционеРа (

Сплит-системы

Kullanım Kılavuzu

Klİma İçİn uzaktan kumanda

(

)

Split tİp

English

Français

Deutsch

Italiano

Español

Português

Nederlands

Ελληνικά

Русский

)

113

Türkçe

127

Table of Contents

Why is my Toshiba WH-H1JE2 remote control not working?
Your remote control may not be working due to several reasons:
Was this helpful?
My Toshiba WH-H1JE2 remote control is not working even with new batteries, what should I do?
If your remote control is not working even with new batteries, consider the following:
- Check if the air conditioner is not working or a power failure has occurred.
- Ensure the power switch of the air conditioner is turned on.
- Verify if the air conditioner is in the ON timer operation.
- Check if the LEDs on the signal receiving part are not in a normal state or the operation mode is incorrect.
- Make sure there are no obstructions blocking signals between the remote controller and the indoor unit's signal receiving part.
- Be aware that rapid start-type or inverter-type fluorescent lights may disturb signal reception.
- Ensure the remote controller is not installed in a place where its signals do not reach the indoor unit.
Was this helpful?
How do I reset my Toshiba WH-H1JE2 remote control?

To reset your remote control, push the RESET button with a fine-tipped tool. This button is used after batteries are replaced or the slide switch is switched.

Was this helpful?
How do I pair my Toshiba WH-H1JE2 remote control with an air conditioner?
To pair your remote control with an air conditioner, you need to match the address setting on the remote with the address switch setting in the signal receiving part of the indoor unit. Up to 6 indoor units can be controlled independently this way.
1. Push the ADR button on the remote control for at least 4 seconds. "Address" will light up on the display, and the current address will flash.
2. Each time you push the ADR button, addresses will change cyclically (ALL → 1 → 2 → 3...→ 6 → ALL). Select an address that matches the address switch setting in the signal receiving part of the indoor unit to be controlled.
3. Push the SET button. The flashing address will change to lighting and be displayed for 5 seconds. If this address matches the address switch setting in the signal receiving part, the buzzer will sound. For details on the address switch setting in the signal receiving part, contact the dealer from whom you purchased the air conditioner.
For more information, see page 13 of the manual.
Was this helpful?
How do I open the battery compartment of the Toshiba WH-H1JE2 remote control?

To open the battery compartment, slide the cover downward while holding both sides of the cover.

Was this helpful?
How do I switch between different operating modes (e.g., cool, heat, fan) using the Toshiba WH-H1JE2 remote?

To switch between different operating modes, push the Mode select button (labeled with a symbol that looks like a cycle arrow). You can select Auto, Heat, Dry, Cool, or Fan by pushing this button.

Was this helpful?
What do the error codes displayed on my Toshiba WH-H1JE2 remote control mean?
When a trouble occurs, a check code is displayed in the Timer time display area on your remote. Additionally, if the LEDs on the signal receiving part flash, it indicates an issue. The meaning of the flashing LEDs depends on the pattern:
- Communication error between the signal receiving part and indoor unit, or address setup error.
- Communication error between the indoor unit and outdoor unit.
- The protective device of the indoor unit is activated.
- The protective device of the outdoor unit is activated.
- Temperature sensor error.
- The compressor of the outdoor unit is protected.
- The air conditioner is performing a test run. If any of these problems remain, it is advised to stop the operation, turn off the power, and notify the dealer with the model name and details of the error.
Was this helpful?
How do I set or cancel a timer function on the Toshiba WH-H1JE2 remote control?
To set or cancel a timer function:
- Setting an OFF timer (to stop operation):
1. Push the Timer button once. The timer symbol and time will flash on the display.
2. Set the desired time using the TIME ▲ or TIME ▼ buttons. The setup time increases or decreases by 0.5 hours, with a maximum of 72.0 hours and a minimum of 0.5 hours.
3. Push the Timer button again. The timer symbol and time will stop flashing.
- Setting a repeat OFF timer (to stop operation repeatedly):
1. Push the Timer button twice. The timer symbol and time will flash on the display.
2. Set the desired time using the TIME ▲ or TIME ▼ buttons.
3. Push the Timer button again. The timer symbol and time will stop flashing.
- Setting an ON timer (to start operation):
1. Push the Timer button three times. The timer symbol and time will flash on the display.
2. Set the desired time using the TIME ▲ or TIME ▼ buttons.
3. Push the Timer button again. The operation mode will disappear, and the timer symbol and time will stop flashing.
- Canceling a timer operation:
  - Push the Timer button. The timer display will disappear. After setting the timer, ensure the remote controller is placed where its signals can reach the signal receiver on the indoor unit.
For more information, see page 9 of the manual.
Was this helpful?
Why is the display screen on my Toshiba WH-H1JE2 remote control blank or dim?

The display screen on your remote control may be blank or dim because the batteries are exhausted. You should replace the batteries.

For more information, see page 11 of the manual.

Was this helpful?
How do I use the basic functions of the Toshiba WH-H1JE2 remote control?
To use the basic functions of the remote control:
- Start/Stop Operation: Push the Start/Stop button to alternately start and stop the air conditioner.
- Select Operation Mode: Push the Mode select button to choose between Auto, Heat, Dry, Cool, or Fan modes.
- Adjust Fan Speed: Push the Fan speed button to select the desired fan speed.
- Set Temperature: Push the Temperature set buttons (▲ or ▼) to adjust the room temperature.
- Adjust Air Direction: Push the Swing/air direction button to set or start swinging the air direction.
- Set Timer: Push the Time setup button for timer settings.
Was this helpful?
What type of batteries does the Toshiba WH-H1JE2 remote control require?

The Toshiba WH-H1JE2 remote control requires two AAA alkaline batteries.

Was this helpful?
What is the effective operating range of the Toshiba WH-H1JE2 remote control?

The standard signal receivable distance from the signal receiving part of the indoor unit is approximately 7 meters. This distance may vary depending on battery capacity and other conditions.

For more information, see page 12 of the manual.

Was this helpful?

Need help?

Do you have a question about the WH-H1JE2 and is the answer not in the manual?

Questions and answers

Summary of Contents for Toshiba WH-H1JE2

Page 1: Remote Controller
(Split type) Wireless remote controller Manuel du proprietaire Generic model name and signal receiving part Télécommande pour climatiseur Français (Type split) RBC-AX31U(W)-E WH-H1JE2 RBC-AX31U(WS)-E (Wireless remote controller Betriebsanleitung model name) Fernbedienung für klimagerät Deutsch (Split-typ) Manuale del proprietario Telecomando per condizionatore Italiano d’aria...
Page 2: Table Of Contents
Owner’s Manual Wireless Remote Controller Kit • Please read this Owner’s Manual carefully for correct use before using your Wireless Remote Controller Kit. Be sure to read “PRECAUTIONS FOR SAFETY” • After you read this manual, please keep it with the Owner’s Manual of the air conditioner in a place where you can access it quickly.
Page 3: Precautions For Safety
Owner’s Manual Wireless Remote Controller Kit PRECAUTIONS FOR SAFETY WARNING WARNINGS ABOUT INSTALLATION • Make sure to ask the qualified installation professional in electric work to install the remote controller. If the remote controller is inappropriate installed by yourself, it may cause electric shock or fire, etc.
Page 4: Part Names And Functions
Owner’s Manual Wireless Remote Controller Kit PART NAMES AND FUNCTIONS Remote Controller (WH-H1JE2) • Up to 8 indoor units in a group can be controlled by one remote controller. RESET button Used after batteries are replaced or the slide switch is switched. (See page 10)
Page 5 Owner’s Manual Wireless Remote Controller Kit Signal Receiving Part • The signal receiving part is attached to the The rear of signal receiving part indoor unit. The following switches are provided on the • Hereinafter, all remote controller button rear of the signal receiving part. For their names are indicated with respective settings, contact the dealer from whom you symbols displayed on the remote...
Page 6 Owner’s Manual Wireless Remote Controller Kit Display section All inticators are shown in the right and the lower figures for the explanation. Only selected contents are display in actual operation. Display • When turning on the leak breaker at the first time, [SET DATA] section flashes on the display part of the remote controller.
Page 7 Owner’s Manual Wireless Remote Controller Kit Operation section Push each button to select a desired operation. • The details of the operation needs to be set up once, afterward, the air conditioner can be used by pushing ON/OFF only. SENSOR Operation select button Start/Stop button Selects the desired operation mode.
Page 8: How To Operate Indoor Unit
Owner’s Manual Wireless Remote Controller Kit HOW TO OPERATE INDOOR UNIT Auto, Heat, Dry, Cool, Fan Stop Push • The automatic cooling/heating and When the operation is stopped with the heating functions are not provided for remote controller, the outdoor unit fan keeps cool-only types.
Page 9: How To Operate The Timer
Owner’s Manual Wireless Remote Controller Kit HOW TO OPERATE THE TIMER • After the timer has been set, put the <Usage Examples> remote controller at a position where ▼ Setting OFF timer signals of the remote controller can reach (Example) To stop operation in the signal receiver on the indoor unit.
Page 10: How To Adjust Air Direction
Owner’s Manual Wireless Remote Controller Kit HOW TO ADJUST AIR DIRECTION • While the air conditioner is not working, the louver (air direction adjusting plate) is closed automatically. • During the preparation for heating, the louver is directed upward and it starts swinging after the preparation for heating is canceled though the automatic louver display on the remote controller shows swinging even during this period.
Page 11: Slide Switch
Owner’s Manual Wireless Remote Controller Kit SLIDE SWITCH • The settings of operation mode display and air direction display vary as follows depending on the indoor unit in use. • Use a fine-tipped tool to change the switch setting. • Push the RESET button after the switch setting is changed. Louver display switch View with the cover removed SENSOR...
Page 12: How To Handle The Remote Controller
Owner’s Manual Wireless Remote Controller Kit HOW TO HANDLE THE REMOTE CONTROLLER • Point the transmitting part of the remote controller at the signal receiving part of the indoor unit. When a signal is received normally, “pi” sound is heard once. (“Pi, pi” is heard only at the beginning of operation.) •...
Page 13: Address
Owner’s Manual Wireless Remote Controller Kit ADDRESS When two or more indoor units controlled by the same wireless remote controller are installed in a room, a unique address can be set for each indoor unit to prevent interference. Up to 6 indoor units can be controlled independently by the remote controller by matching the address switch setting of the signal receiving part with the address displayed on the remote controller.
Page 14: How To Perform Emergency Operation
Owner’s Manual Wireless Remote Controller Kit HOW TO PERFORM EMERGENCY OPERATION In the event of an emergency shown below, push emergency operationeon the signal receiving part (inside the ceiling panel or indoor unit) for emergency operation. • The batteries of the remote controller have been exhausted. •...
Page 15: Before Asking For Repair Work
Owner’s Manual Wireless Remote Controller Kit BEFORE ASKING FOR REPAIR WORK Check the following before asking for repair work. Check again Phenomenon Possible cause Measures Operation does The air conditioner is not working or a power failure Push on the remote controller again. not start even if has occurred.

This manual is also suitable for:

Rbc-ax31u(w)-e Rbc-ax31u(ws)-e Rbc-ax31u-e

Toshiba WH-H1JE2 Owner's Manual

Quick Links

Remote Controller

Model name:

Frequently Asked Questions (12)

Need help?

Questions and answers

Related Manuals for Toshiba WH-H1JE2

Summary of Contents for Toshiba WH-H1JE2

This manual is also suitable for:

Table of Contents