RETEKESS TA003 & TA004 - Receiver & Transmitter Manual

Features
Figure A:

Figure B:

6. ANTENNA: The antenna attaches here using the BNC connector.
7. CHANNEL: This button changes the channel the transmitter is using. Press to toggle between channel 1, 2, 3, etc. The LED display will show the currently selected channel. Notes: When more than two transmitters are working simultaneously, make sure each transmitter on a different channel.
8. DC-9V: Connect the power adapter here to power the unit and charge the internal battery. While the transmitter is plugged in, it can be operated in high power mode. (See Fig A. Item #4)

Getting Connected

The transmitter is easily wired into any system, just fllow these steps:

1. Attach the antenna to the transmitter (Arrow #1)
2. Connect a cable from the Audio Output on the music source to the RCA Audio Input located on the Silent Symphony transmitter. (Diagram pg 3)
3. Connect a microphone to the 1/8" input on the transmitter to be mixed with the audio signal. (Diagram pg 3)
4. Select the Transmission Power Level. (Pg 2, Fig A, Item #4)
5. Select from one of the available frequencies to broadcast on with the Channel Select switch. (Arrow #2)
6. Power your headset receiver(s) ON and select the appropriate channel to listen with the Tune button.
7. Adjust the headset receiver volume to a comfortable listening level.

With this setup, any audio that is fed into the transmitter will be broadcast wirelessly to all headset receivers tuned to the same channel and that are within its operational range.
Note: The transmitter will power off if no input signal is detected after 5 minutes.

Use RCA to 1/8" Female, connect to 1/8" Male to 1/8" Male, then out to Laptop, Phone, Tablet
Do Not Connect Mini USB Charging Cable to Transmitter

SECTION B: HEADPHONE RECEIVER

What's in the box

Receiver Box

• 1 * Headphone receiver
• 1 * USB charging cable
• 1 * User Manual

Features:

• Transmits audio signal about 300M, through walls, floors and ceilings.
• Active noise reduction system for crystal clear sound
• Advanced 40mm speaker for outstanding sound performance
• Double PLL system for ultimate frequency stability
• Big channel-indicating logo light, you can see the channel difference by logo color change
• Soft leatherette ear cushions and robust headband let you listen to your entertainment in extreme comfort, even during long hours of extended wear
• With Shock-Resistant, Robust Metal Headband
• Endless headphones can be used simultaneously with one transmitter
• Auto mute and automatic shut-off after 10 minutes of no signal detection, conserve battery life

Operation:

1. POWER/TUNE: Hold the power button for ~3 seconds to turn the headphones on and off.
   Press the power button once to change the selected channel. The LED lights will change to display the currently selected channel.
   Channel 1 – Red
   Channel 2 – Green
   Channel 3 – Blue
   
   
2. VOLUME/LED: Move the switch to the left to increase volume, move to the right to decrease volume. Press the switch in and hold for ~2 seconds to toggle the LED light mode. LED will toggle between always on and off.
   

FAQ / Troubleshooting

Why am I not hearing any sound from the headset receiver(s)?

• Make sure the headset receivers are tuned to the same channel as the transmitter.
• Double check volume levels at:
  Music source
  Any sound equipment connected to the transmitter
  Headset receiver(s)
• Double check the connections from the Music Source to the Audio Input.
• Ensure the internal batteries are fully charged for both the transmitter and headset.

How many receivers can work at once?

• There is no limit to the number of receivers that can be in one area.

Is there a pairing process to add additional headset receiver(s)?

• No, there is no pairing process other than selecting the appropriate channel with the TUNE button located on the headset receiver(s).

How far does the transmitter reach when on high and low settings?

• On the high setting, the operational range is approximately 300ft.
• On the low setting, the operational range is approximately 100ft.

What is the expected battery life for the headphones and for the transmitter when being used remotely?

• The headphones can run for about 8 hours continuously, and transmitter can run for about 5 hours continuously before needing to be charged.
• Please allow at least 6 hours of charging time.

SPECIFICATION

Henan Eshow Electronic Commerce Co., Ltd
Add: 7/F, Sanjiang Building, No.170 Nanyang Road, Huiji District,
Zhengzhou, Henan, China
Facebook: facebook.com/Retekess.ru
E-mail: support@retekess.com.ru
Web: retekess.com.ru

MADE IN CHINA