Advertisement
Grow Wall 3
Thank you for purchasing OPCOM Farm Grow Wall 3 , the indoor hydroponics growing system. lt is designed for easy to use and
efficient growth by one-touch AUTO mode.lt holds up to 144 plants capacity. Please read the quick guide carefully before setting it up.
For detailed user guide video, please visit Grow Wall 3 page at http://www.opcomfarm.com
A. Assembly
A1. Remove all the parts from box and check all the accessories
Fan power
LED4
fan beam
power
Conrtol
Box
R3
column
L4 planting groove
LED3
power
L3 planting groove
R2
LED2
column
power
L2 planting groove
LED1
power
Pump
R1
power
L1 planting groove
column
Water tank
A2. Assemble GrowWall 3
Assemble the left and right three short column into two left
1
and right column.
2
Hang the four planting groove on the four screws of different
heights on the column, and fasten with a pull buckle to fix it.
Place the top beam on the top of the column and fix it with
3
a buckle.
Assemble two wall brackets in a rotating manner behind the
4
top beam and tear off the double-sided tape and stick to the
wall.
Rotate the downspout up and down and disassemble it into
5
an upper downspout and a lower downspout.
After nest the upper downspout with metal gaskets and
waterproof gaskets through the drain hole at the bottom of
the planting groove, rotate the lower downspout from the
bottom of the planting groove to the upper downspout tightly.
Hang the L-shaped hard pipe of the upper water pipe on the
6
right side of the uppermost planting groove, pass the hose
below the L-shaped hard pipe through the pipe groove of the
right column, nest the end of the hose over the port on the
right side of the water tank above the pump pack.
7
Put four filter sponges on the upper downspout in the four
planting groove, one filter sponge on the filter in the water
tank, and cover the four planting trays on the four planting
groove respectively.
Lock the four LED grow lights to the four light arms using the screws you removed from two sides of the LED grow lights.
8
Connect the 6 round hole plugs plugged into the main line of the control box to the fan (Fan), the motor (Pump) and the 4 LED growth
9
lights respectively, and insert the power supply plug of the control box into the socket. Insert the cable tie terminal corresponding to the
main line into the corresponding hole of the right column.
Assembly
Top water
Downpipes
Wall support
pipe x 1pc
x4pcs
column x2pcs
column x 6pcs
Top beam x1pc
Water tank x1pc
Grow Kits
Salt #1
Planting Tray
Seedling Tray x2pcs
Grow Sponge 60pk
planting basket
(Nutrition)
(36 holes) x4pcs
(665*175*65mm)
x9pcs (OASP001)
(25mm) x150pcs
250ml x2
Accessories
Alkaline
Neutral
Acidic
Water
Cleaning
EC test
PH test
Filter
Spray x1pc
ponge x1pc
pen x1pc
paper x1pc
Sponge x5pcs
3
2
2
5
5
9
1
Water Control Box:
1. Open the water control box on the left side of the water tank by pulling up the side planks. Take out the water drain pipe form the
storing disk.
2.Prepare a water bucket with a capacity of around 40 L. Place the outlet of thepipe un the bucket. Press the Pump button to turn on
the pump and switch the water drain valve to 'Out' to start draining.
3.Once finished draining, press the Pump button to turn off the pump and switch the water drain valve to 'Stop' to stop draining.
Set everything back to default.
Chart I: Control Box
Smart Control Box
LED Growth Light x4pcs
A3. LED light planting mode Control
1. Select the mode of the LED grow light (you may switch between modes through the button on the left side of the LED lamp
planting groove x4pcs
holder)(see figure 1), the light comes with two modes: G and L.
2. Height of the LED grow light: Adjust the height and the angle of lighting manually through the rocker arm(see figure 2).
3. This hydroponics system comes with fans that improve the air circulation and accelerate the cooling of the LED tubes, which
increases the ventilation and avoids plants from overheating. Please make sure to keep a 5-10 cm distance between the light
Soda
Lemon
B Scoop for
(pH+)
(pH-)
Adjust of
tube and the plants to further prevent plants from overheating. To boost the light intensity in a power-saving way, direct the
50ml x1
50ml x2
Nutritio (5g)
light at both the plant and the wall simultaneously, which could add 30% more lighting to the plants.
Warranty
Manual
Card
4
Please read and follow every steps to avoid any malfunction.
B. Seedling
B1. Germination Stage
9
9
1. Add water to the seedling tray, up to the water (red) level.(Fig1)
2. Open Grow Sponge package,put each sponge piece into water of seedling tray (make sure the
front side with the seed label is side up), press the sponges into water 5 seconds and ensure the
6
9
sponges absorb water completely. Put seed moisturizing cover on the sponges.(Fig2)
3. Place the seedling tray with cover in the shade.(Fig3)
4. Suggest using Watering Spray water to sponges and keep them wet
6
everyday.
5. During 0 ~ 7 days, find the sprouted ones in the tray; pick them out, and
move them into product and to next stage: B2. Young Plant Stage.
7
6. Discard unsprouted sponges after regular germination time.
7. In each sponge, keep strong plants and cut the other weak plants.
* Different plant may have different germination time, please check before plant.
7
Chart II: Plant Stage
Basil, Lemon Balm
6
Germination Stage
Young Plant Stage
Growing Stage
7
* Please keep the seeds in refrigerator if you don't use it, recommended temperture is 41
* For your expected plant amount, you can refer to the sprout rate of 1st planting cycle.
* If you need more planting information, please vist to www.opcomfarm.com and read "Plant Q&A".
EC value Status
Adjustment method
Fuction
Status
Operation
Panel Light
Wifi pairing
Long press 5 sec
LED
ON
One Press
OFF
One Press
ON
One Press
Fan
OFF
One Press
ON
One Press
Pump
OFF
One Press
Restore factory settings after power failure.
Fuction
Operation
Operation
Status
Switch to G
G
LED grow
light planting
Switch to OFF
OFF
mode
Switch to L
L
figure 1
Adjust the height of lighting
Planting Time
LED Mode
Pump Mode
Nutrition
T
( )
Don't need
Day 0~7
OFF
OFF
68 - 77
Day 3~14
G Mode
ON
Need
59 - 86
After Day 14
L Mode
Free setting
Need
59 - 86
50.
-
when 0.0-0.5
when 0.5-1.0
when 1.0-1.5
Add 2g Salt #1
Add 1g Salt #1
Standard range
Water Cycling Valve
Water Drain pipe
Water Drain Valve
Water Cycling Valve
11 gallons
（40L）
Adjust the angle of lighting
figure 2
Fig1
Fig2
Fig3
RH
EC
PH
Notes
Be sure each sponge is fully wet in
80%
0.5-1.0
5.5-6.5
seedling tray.
45%-70%
1.0-2.0
5.5-6.5
45%-70%
1.0-2.0
5.5-6.5
when over 2.0
Add water
Advertisement
