Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for InfiRay FB4-T
Summary of Contents for InfiRay FB4-T
- Page 1 Dual-spectrum Bullet Network Camera Quick Start Guide V1.0.2...
-
Page 2: Important Safety Notice
Dual-spectrum Bullet Network Camera Quick Start Guide Preface The following is about the correct use of the camera. In order to prevent danger and loss of property, please read this manual carefully before using the camera and strictly follow it during use. Please keep the manual properly after reading. - Page 3 Dual-spectrum Bullet Network Camera Quick Start Guide product labels.) In order to make emergency power off when necessary, please install power-off equipment which is easy to use when installing the wires. Please protect power lines from being treaded or pressed, especially the connecting points which are led from the plug, power socket or other unit.
- Page 4 Dual-spectrum Bullet Network Camera Quick Start Guide Soft dry cloth can be used to clean the camera. For the dirt difficult to clean, please use soft cloth with little neutral detergent and then wipe dry. Do not use volatile detergent like alcohol, benzene or diluent, or strong and abrasive detergent, otherwise the camera coating would be damaged and also the camera performance could be degraded.
- Page 5 Dual-spectrum Bullet Network Camera Quick Start Guide Requirements for lifting equipment: Safe lifting equipment suitable for site and method of camera installation. The lifting equipment is able to reach enough height of installation position. The lifting equipment has good safety performance.
-
Page 6: Table Of Contents
Dual-spectrum Bullet Network Camera Quick Start Guide Table of Contents Important Safety Notice................I 1. Camera Introduction..............- 1 - 1.1 Camera Description..............- 1 - 1.2 Camera Features..........错误！未定义书签。 1.3 Camera Appearance..............- 1 - 1.4 Cable Introductions..............- 2 - 1.5 Alarm Interface Connection.............- 3 - 2. -
Page 7: Camera Introduction
Dual-spectrum Bullet Network Camera Quick Start Guide 1. Camera Introduction 1.1 Camera Description Dual-spectrum bullet network camera is a new-type thermal imaging net camera integrated with the functions of infrared imaging and high definition visible light. Equipped with advanced passive infrared imaging detectors, industrial thermographic analysis tools, smoke &... -
Page 8: Cable Introductions
Dual-spectrum Bullet Network Camera Quick Start Guide 1.3 Cable Introductions The cable includes interfaces for power, alarm, audio, RS-485, and RJ-45 network, etc. Please see the following figure for interface instructions. Figure 1.2 Cable Introductions P1 network interface (LAN): Output network signal and connect to standard Ethernet cable. -
Page 9: Alarm Interface Connection
Dual-spectrum Bullet Network Camera Quick Start Guide P6 is alarm output (ALARM OUT): alarm output interface, among which pin_1（ALARM-OUT1） and pin_2(ALARM-COM1) are channel 1 alarm output; pin_3(ALARM-OUT2) and pin_4 (ALRAM-COM2) is channel 2 alarm output. P7 RS-485 interface (RS485):it is used for connecting to the peripherals ... -
Page 10: Instructions Before Installation
Dual-spectrum Bullet Network Camera Quick Start Guide 2.1 Instructions before Installation Before installation, please confirm that the camera in the package is in good condition and all parts are complete. The installation wall should have a certain thickness, and can bear at least 4 times the weight of the camera and installation accessories. -
Page 11: Recommended Monitoring Distance
Dual-spectrum Bullet Network Camera Quick Start Guide 2.2 Recommended Monitoring Distance Since the thermal imaging channel of the camera adopts a fixed-focus athermalized lens, remote electric focusing can not be realized. Therefore, before installing the camera, please select the corresponding installation position and lens focal length according to the monitoring requirements to achieve the purpose of monitoring. -
Page 12: Installation Guide
Dual-spectrum Bullet Network Camera Quick Start Guide direction. Recognizing the target needs to image no less than 6 pixels in the critical direction. Recognizing the target requires imaging no less than 12 pixels in the critical direction. The actual detection distance varies with the settings of the thermal ... -
Page 13: Wall Mounting/Ceiling Mounting
Dual-spectrum Bullet Network Camera Quick Start Guide Figure 2.3 TF Card Installation Step 3: After installation, close the TF card slot cover and tighten the screws. Wall Mounting/Ceiling Mounting 2.3.2 Step 1 Mounting Sticker Please paste the sticker attached on the selected installation wall, and then punch four Φ5 installation holes according to the label on the sticker. - Page 14 Dual-spectrum Bullet Network Camera Quick Start Guide Figure 2.4 Mounting Sticker Step 2 Mounting Camera Figure 2.5 Wall Mounting Pass the tail wire of the camera through the A hole, then use the attached self-tapping screws to fix the camera to the wall. The wall mount is shown in Figure 2.5, and the ceiling mount is shown in Figure 2.6.
-
Page 15: Install Network Port Protective Cover
Dual-spectrum Bullet Network Camera Quick Start Guide Figure 2.6 Ceiling Mounting Step 3 Adjust Monitoring Angle Use the equipped L-shaped hexagonal wrench to loosen one lock nut near the camera bracket, adjust it to a predetermined position by turning or rotating it, and then tighten the lock nut, as shown in the figure below. Figure 2.7 Three-axis Adjustment 2.4 Install Network Port Protective Cover When using the camera, install the matching network port waterproof cover... -
Page 16: Operation Guide
Dual-spectrum Bullet Network Camera Quick Start Guide Step 2 Scissor the waterproof rubber ring and put it on the network cable between the main body of the waterproof cover and the fastening nut. Step 3 Put the O-shaped rubber ring into the network port, and insert the network cable into the network port. -
Page 17: Login System
Dual-spectrum Bullet Network Camera Quick Start Guide your computer's IP address to the same network segment with the network video server, and the same subnet mask. Such as: 192.168.1.120. 3. Test whether the device starts normally. Under WINDOWS, follow the <Start→run→cmd>... -
Page 18: Main Interface Description
Dual-spectrum Bullet Network Camera Quick Start Guide Figure 3.2 Preview Interface 3.3 Main Interface Description On the Web interface of the camera, you can perform operations and configurations such as preview, video playback, temperature measurement analysis, intelligent analysis, and parameter setting. 1. -
Page 19: Appendix A Camera Maintenance
Dual-spectrum Bullet Network Camera Quick Start Guide Appendix A Camera Maintenance Lens Maintenance The lens surface is coated with anti-reflective coating. When contaminated with dust, grease, and fingerprints, harmful substances will be produced, therefore the degraded performance, cratches or mold will be caused. Once dirt is found, please follow the following methods. -
Page 20: Appendix B Emissivity Of Common Materials
Dual-spectrum Bullet Network Camera Quick Start Guide Appendix B Emissivity of Common Materials Materials Temperature（℃） Emissivity Water 0～100 0.95～0.98 Soil(dry) 0.92 Soil(wet) 0.95 Woods 0.962 Sand Sandstone 0.909～0.935 PVC plastic 0.93 Asphalt 0.967 Paint 0.92～0.94 Wallpaper 0.85～0.90 Cloth 0.98 Concrete 0.92 Pavement surface 0.974...