Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for InfiRay FD2-T
Summary of Contents for InfiRay FD2-T
- Page 1 Dual-spectrum Turret Network Camera Quick Start Guide V1.0.3...
- Page 2 Dual-spectrum Turret Network Camera Quick Start Guide Preface The following is about the correct use of the camera. In order to prevent danger and loss of property, please read this manual carefully before using the camera and strictly follow it during use. Please keep the manual properly after reading.
- Page 3 Dual-spectrum Turret Network Camera Quick Start Guide In order to make emergency power off when necessary, please install power-off equipment which is easy to use when installing the wires. Please protect power lines from being treaded or pressed, especially the connecting points which are led from the plug, power socket or other unit.
- Page 4 Dual-spectrum Turret Network Camera Quick Start Guide to clean, please use soft cloth with little neutral detergent and then wipe dry. Do not use volatile detergent like alcohol, benzene or diluent, or strong and abrasive detergent, otherwise the camera coating would be damaged and also the camera performance could be degraded.
- Page 5 Dual-spectrum Turret Network Camera Quick Start Guide Safe lifting equipment suitable for site and method of camera installation. The lifting equipment is able to reach enough height of installation position. The lifting equipment has good safety performance.
-
Page 6: Table Of Contents
Dual-spectrum Turret Network Camera Quick Start Guide Table of Contents 1. Camera Introduction ..............- 1 - 1.1 Camera Description ..............- 1 - 1.2 Camera Features ..........错误！未定义书签。 1.3 Camera Appearance ..............- 1 - 1.4 Cable Instructions ..............- 2 - 1.5 Alarm Interface Connection ............ -
Page 7: Camera Introduction
Dual-spectrum Turret Network Camera Quick Start Guide 1. Camera Introduction 1.1 Camera Description Dual-spectrum turret network camera is a new-type thermal imaging net camera integrated with the functions of infrared imaging and high definition visible light. Equipped with advanced passive infrared imaging detectors, industrial thermographic analysis tools, smoke &... - Page 8 Dual-spectrum Turret Network Camera Quick Start Guide 1.3 Cable Introductions The cable includes interfaces for power, alarm, audio, RS-485, and network, etc. Please see the following figure for interface instructions. Figure 1.2 Cable Introductions P1 network interface (LAN): Output network signal and connect to standard Ethernet cable.
-
Page 9: Alarm Interface Connection
Dual-spectrum Turret Network Camera Quick Start Guide 1.4 Alarm Interface Connection The camera can be connected with alarm switch signal (0~DC 5V) input and switch output (no voltage). An external power supply is required when connecting the alarm. The specific wiring method is shown in the figure below. -
Page 10: Recommended Monitoring Distance
Dual-spectrum Turret Network Camera Quick Start Guide directly. When transporting the camera, do not directly pull the cable at the end of the camera, otherwise it may affect the waterproof performance of the camera or cause wiring problems, as shown in the figure below. Figure 2.1 Incorrect Handling of the Camera 2.2 Recommended Monitoring Distance Since the thermal imaging channel of the camera adopts a fixed-focus... - Page 11 Dual-spectrum Turret Network Camera Quick Start Guide The reference table of lens focal length and monitoring distance is shown in the following table. - 5 -...
-
Page 12: Installation Guide
Dual-spectrum Turret Network Camera Quick Start Guide Table 2.1 Recommended Monitoring Distance（12μm Pixel） Equipped Lens (Vehicles) (Human) (Vehicles) (Human) (Vehicles) (Human) 256m 3.2mm 409m 133m 102m 894m 292m 224m 112m If the weather is clear and the visibility is normal, without visible fog or haze, there is a 50% chance of reading the target at the specified distance. - Page 13 Dual-spectrum Turret Network Camera Quick Start Guide 2.3.1 TF Card Installation Step 1: The TF card slot is located below the device. Use the cross screwdriver to unscrew the TF card slot cover, as shown below. Figure 2.2 Unscrew TF Card Slot Cover Step 2: Insert the TF card slowly into the card slot in the direction indicated by the arrow.
- Page 14 Dual-spectrum Turret Network Camera Quick Start Guide 2.3.2 Wall Mounting/Ceiling Mounting Step 1 Mounting Alignment Guide Please paste the sticker attached on the selected installation wall, and then drill four Φ5 installation holes according to the markers on the alignment guide. The recommended depth is 35mm. The alignment guide is shown in Figure 2.4.
- Page 15 Dual-spectrum Turret Network Camera Quick Start Guide Figure 2.5 Wire Hole of the Base Figure2.6 Wall Mount - 9 -...
- Page 16 Dual-spectrum Turret Network Camera Quick Start Guide Figure 2.7 Ceiling Mount Step 3 Adjust Monitoring Angle Adjust the angle of the sphere by hands, adjust it to a predetermined position by turning or rotating it, and then tighten the lock nut, screw the gland with ornament to the base, as shown in figure 2.8.
-
Page 17: Install Network Port Protective Cover
Dual-spectrum Turret Network Camera Quick Start Guide 2.4 Install Network Port Protective Cover When using the camera, install the matching network port waterproof cover to prevent water from entering the network cable. Please install it if necessary. The installation steps are as follows: Step 1 Pass the network cable through the fastening nut and the main body of the waterproof cover in turn. -
Page 18: Operation Guide
Dual-spectrum Turret Network Camera Quick Start Guide 3. Operation Guide 3.1 Preparations 1. The default IP address of the device：192.168.1.123. 2. The subnet mask is 255.255.255.0, and the IP address of the camera can be modified. If you change the device address to 192.168.1.194, change your computer's IP address to the same network segment with the network video server, and the same subnet mask. - Page 19 Dual-spectrum Turret Network Camera Quick Start Guide Figure 3.1 Login Interface 2. For the first login, the admin user/password by default: （admin/admin） , you can perform other operations only after the password is changed. 3. The third-level user login: admin (defaulted, administrator user) or operator (operator user) or user (ordinary user)), to login after typing in the password.
-
Page 20: Main Interface Description
Dual-spectrum Turret Network Camera Quick Start Guide 3.3 Main Interface Description On the Web interface of the camera, you can perform operations and configurations such as preview, video playback, temperature measurement analysis, intelligent analysis, and parameter setting. 1. Preview: Used for image preview and operation control. 2. -
Page 21: Appendix A Camera Maintenance
Dual-spectrum Turret Network Camera Quick Start Guide Appendix A Camera Maintenance Lens Maintenance The lens surface is coated with anti-reflective coating. When contaminated with dust, grease, and fingerprints, harmful substances will be produced, therefore the degraded performance, cratches or mold will be caused. Once dirt is found, please follow the following methods. -
Page 22: Appendix B Emissivity Of Common Materials
Dual-spectrum Turret Network Camera Quick Start Guide Appendix B Emissivity of Common Materials Materials Temperature（℃） Emissivity Water 0～100 0.95～0.98 Soil(dry) 0.92 Soil(wet) 0.95 Woods 0.962 Sand Sandstone 0.909～0.935 PVC plastic 0.93 Asphalt 0.967 Paint 0.92～0.94 Wallpaper 0.85～0.90 Cloth 0.98 Concrete 0.92 Pavement surface 0.974...