1. Warning and precautions for safety Please observe the following safety precautions in order to use safely and correctly the refrigerator and to prevent accident and danger during repair. 1. Be care of an electric shock. Disconnect power cord from wall outlet and wait for more than three minutes before replacing PCB parts.
3. Basic parameters BD-590WYHC1(H) Content Unit Value Voltage/frequency 115 / 60Hz Gross capacity (fridge/freezer) 21.2cu.ft/599L cu.ft/L Climate 12.8~43.3℃ class(SN=10~32℃,N=16~32℃,ST=16~38℃,T=16~43 ℃) kWh/year Energy consumption / year kWh/24 h 1.504 Energy consumption (EN153) per 24 h R / g R600a/55g Kind of coolant /Charge ( 134 /R600a) / grammes Foaming components (R141b/C-P)...
Page 11
Fast Freeze will quickly lower the show “OF” . If no buttons have been temperature within the freezer so food pressed, the display board will turn off will freeze faster than usual. This about 1 minute later. feature also helps to keep vitamins and IF you want to turn off the power ...
4.3 Installing handles Before you use the appliance, you have to install the handles provided in the fridge chamber. Please follow procedures below to install and reverse the handle. Fasten the handle supports (C) to the door by a cross screwdriver (self-provided). ...
4.4 Defrost mode 4.4.1 Automatic defrost mode When compressor accumulated running time reach the setting point (depends on the environment temperature), it will enter defrost mode automatically. 4.4.2 Force Defrosting Mode Within 10 minutes of power on, press the button “ ”...
5.Trouble shooting 5.1 Error Code Code Problem Freezer sensor malfunctions Freezer defrost sensor malfunctions Freezer fan malfunctions Communication sending malfunctions Communication receiving malfunctions 5.2 Common problem and checking If you experience a problem with your appliance or are concerned that the appliance is not functioning correctly, you can carry out some easy checks before calling for service, please see below.
Page 15
Gurgling sound similar to water boiling. Popping noise during automatic defrosting. Clicking noise before the compressor starts. Other unusual noises are due to the reasons below and may need you to check and take action: The cabinet is not level. The back of appliance touches the wall.
6. Circuit and checking 6.1 Circuit diagram 6.2 Main control board 6.2.1 Checking method If the problem is probably caused by main control board, change it directly to confirm. 6.2.2 Removing the main control board 1. Unplug the appliance 2. Remove the screws by screwdriver and remove the electric box cover, as picture 1 and picture 2.
Page 25
electric box cover and check. 2.Check the connecting wiring between compressor and main control board and repair if it is broken. 3、Use a multimeter to measure voltage between pin No.1 and No.5 on 7pins connector of main control board. If the voltage equal to electric supply power, it means the main control board is OK, to change t change the main control board.
6.4 Fan motor 6.4.1 Basic parameters 6.4.1.1 Fan motor Rated voltage:DC12V 6.4.2 Checking method 1. Check the connecting wiring of fan motor is well or not, repair if it is broken. The fan motor corresponding pin No.1~3 on 5pins connector of main control board. 2.
6.5 Light 6.5.1 Basic parameters Rated voltage:DC12V Rated power:5W 6.5.2 Checking method 1.Check the connecting wiring between light and main control board is well or not, repair if it is broken. The light corresponding pin No.4 and No.5 on 5 pins connector of mainboard. 2.Check output voltage corresponding light of the main control board, if it is 12V when working conditions are met, it means the mainboard is OK, change the light;...
Door switch corresponding pin No.7 and No.8 on 8pins connector of the mainboard. 2. Check the magnet on the door is dropped out or not. 3. Normally, when the door is closed, the two pins of door switch should be short circuit; when the door is open, the two pins should be open circuit.
Rated power: 230W 6.8.2 Checking method 1.Enter force defrost mode, use a multimeter to measure the voltage between pin No.2 connector of the main control board, if the voltage doesn’t equal to and No.7 on 7pins electric supply power, it means the main control board is broken, change it. 2.
Page 30
temperature decreases 1 ℃ the corresponding resistor value would increase about 100ohm. But it is not linear relationship between resistance and temperature, so it's just an estimation algorithm. You'd better measure the following temperature resistance is more accurate, and more likely to get the temperature.
7. Cooling system repairing 7.1 Refrigeration system Compressor discharges high temperature high pressure R600a gas refrigerant Refrigerant enters anti-condensation pipe, condenser, then becomes middle temperature high pressure liquid after condensation Refrigerant enters dry filter,water and imperity will be filtrated Refrigerant enters Electromagnetism valve, and Capillary, then pressure will be reduced Refrigearnt enters finned evaporator and become low temperature low pressure gas after...