Tecnoautomazione T182A User Manual

T182A.
ON
3 4 5 6 7 8 9 10
1 2
LEFT / DIP-SWITCH
RC1 RC2
R1
R2
REMOTE
R3
R4
TIME
A
B
C
OBSTACLE
1 2 3 4 5 6 7
INPUT
INTERNAL
RECEIVER
LEDs:
S1.S2.S3. GATE STATUS / CONTROL BOARD STATUS LEDS
RC1.RC2.R1.R2.R3.R4. RADIO LEDS
RC1. SHOWS THAT A SIGNAL HAS BEEN RECEIVED FROM THE INTERNAL RADIO RC1
RC2. SHOWS THAT A SIGNAL HAS BEEN RECEIVED FROM THE EXTERNAL RADIO RC2
R1. START: INDICATES THAT A START BUTTON ON THE REMOTE HAS BEEN PRESSED
R2. STOP: INDICATES THAT A STOP BUTTON ON THE REMOTE HAS BEEN PRESSED
R3. PEDESTRIAN: SHOWS THAT A START PEDESTRIAN BUTTON ON THE REMOTE HAS BEEN PRESSED
R4. OUT1 ON/OFF: SHOWS THAT A OUT1 BUTTON ON THE REMOTE HAS BEEN PRESSED
A.B.C. PROGRAMMING LEDS
1.2.3.4.5.6.7. INPUTS
AUSILIARY OUTPUTS:
EXPANSION RELAY MODULE - OUT1. ENABLED/DISABLED VIA REMOTE (FUNCTION R4). IF THE RIGHT DIP10 IS ON, THE OUT1 IS ON FOR 3 MIN
AFTER EACH OPENING PHASE.
EXPANSION ELECTRIC-LOCK MODULE OUT2. ENABLED AT OPENING FOR 3 SEC.
LEFT DIP-SWITCH (1) FUNCTIONS
MOTORS POWER. DIP 1 - 2.
OFF / OFF = 40%
1 2 3 4 5 6 7 8 9 10
ON / OFF = 60%
1 2 3 4 5 6 7 8 9 10
OFF / ON = 80%
1 2 3 4 5 6 7 8 9 10
ON / ON = 100%
1 2 3 4 5 6 7 8 9 10
SLOW DOWN. DIP 3.
OFF = DISABLED
1 2 3 4 5 6 7 8 9 10
ON = ENABLED
1 2 3 4 5 6 7 8 9 10 POWER 100%
OBSTACLE DETECTION SENSOR. DIP 4.
OFF = DISABLED
1 2 3 4 5 6 7 8 9 10
ON = ENABLED
1 2 3 4 5 6 7 8 9 10
ELECTRONIC LIMIT SWITCH. DIP 5.
OFF = DISABLED
1 2 3 4 5 6 7 8 9 10
ON = ENABLED
1 2 3 4 5 6 7 8 9 10
SWING GATE CONTROL UNIT. POWER SUPPLY 230 VAC. FREQUENCY 433.92 MHz. 100 STORABLE CODES.
3 4 5 6 7 8 9 10
1 2
RIGHT / DIP-SWITCH
EXTERNAL
RECEIVER
8 9 10 11 12
SOFT START. DIP 6 - 7.
1 2 3 4 5 6 7 8 9 10
1 2 3 4 5 6 7 8 9 10
1 2 3 4 5 6 7 8 9 10
1 2 3 4 5 6 7 8 9 10
GATE LEAVES DELAY. DIP 8 - 9.
1 2 3 4 5 6 7 8 9 10
1 2 3 4 5 6 7 8 9 10
1 2 3 4 5 6 7 8 9 10
1 2 3 4 5 6 7 8 9 10
MOTORS AND PHOTOCELLS TESTS. DIP 10.
1 2 3 4 5 6 7 8 9 10
1 2 3 4 5 6 7 8 9 10
5A FUSE
13 14 15 16 17 18
A MOTOR B MOTOR
MODES. DIP 1 - 2.
OFF / OFF = 0.1 sec OFF / OFF = AUTOMATIC CLOSURE
1 2 3 4 5 6 7 8 9 10
ON / OFF = 0.5 sec ON / OFF = COMMUNITY MODE
1 2 3 4 5 6 7 8 9 10
OFF / ON = 1.0 sec OFF / ON = STEP-BY-STEP MODE
1 2 3 4 5 6 7 8 9 10
ON / ON = STEP-BY-STEP + AUTOMATIC
ON / ON = 1.5 sec
1 2 3 4 5 6 7 8 9 10
ELECTRIC-LOCK. DIP 3 - 4.
OFF / OFF = 0 sec
1 2 3 4 5 6 7 8 9 10
ON / OFF = 3 sec
1 2 3 4 5 6 7 8 9 10
OFF / ON = 6 sec
1 2 3 4 5 6 7 8 9 10
ON / ON = 12 sec
1 2 3 4 5 6 7 8 9 10
FAST CLOSURE. DIP 5.
OFF = DISABLED
1 2 3 4 5 6 7 8 9 10
ON = ENABLED
1 2 3 4 5 6 7 8 9 10
OIL RECIRCULATION. DIP 6.
1 2 3 4 5 6 7 8 9 10 11 12
1 2 3 4 5 6 7 8 9 10 11 12
INPUTS:
1. START OR OPEN N.O.
2. STOP N.C.
3. EXTERNAL PHOTOCELL N.C.
closing phase: inverts the gate movement
4. INTERNAL PHOTOCELL N.C.
opening phase: pauses the gate movement
closing phase: inverts the gate movement
G
R
5. MOTOR «A» LIMIT SWITCHES N.O.
O
U
N
6. MOTOR «B» LIMIT SWITCHES N.O.
D
7. PEDESTRIAN OR CLOSE N.O
N L
230 VAC
S1 S2 S3 BOARD STATUS:
x
STAND BY, GATE CLOSED
19 20
GATE IN OPENING OR CLOSING PHASE,
GATE OPEN
PROGRAMMING OF WORKING TIMES /
OBSTACLE SENSOR
PROGRAMMING ERROR
PHOTOCELLS ERROR
MOTOR A ERROR:
A
CONNECTION
B ERROR OR MOTOR
OVERHEATING
C
MOTOR B ERROR:
A
CONNECTION
B ERROR OR MOTOR
OVERHEATING
C
RIGHT DIP-SWITCH (2) FUNCTIONS
1 2
1 2
CLOSURE
DISABLED NOT WIRED N.C. INPUTS. DIP 8.
OFF / OFF = STANDARD
1 2
ON / OFF = KICK BACK AT
CLOSING 1 sec
OFF / ON = KICK BACK AT
OPENING
ON / ON = KICK BACK AT
1 2
CLOSING + KICK BACK AT
OPENING
OFF = DISABLED
1 2
ON = ENABLED
1 2
OFF = DISABLED
1 2
ON = ENABLED
1 2
A
OBSTACLE
B
DETECTED
C
A
OBSTACLE
B
DETECTED
C
MODE 1 OR 2 MOTORS. DIP 7.
OFF =
2 MOTORS MODE
3 4 5 6 7 8 9 10
ON =
1 MOTOR MODE
3 4 5 6 7 8 9 10
OFF =
N.C. INPUTS ENABLED
3 4 5 6 7 8 9 10
ON =
NOT WIRED N.C.
3 4 5 6 7 8 9 10 INPUTS DISABLED
INPUTS OPTION 1 - 7. DIP 9.
INPUT 1 = START
OFF =
3 4 5 6 7 8 9 10 11 12
INPUT 7 = PEDESTRIAN
INPUT 1 = OPEN
ON =
3 4 5 6 7 8 9 10 11 12 INPUT 7 = CLOSE
COURTESY LIGHT. DIP 10.
OFF = DISABLED
3 4 5 6 7 8 9 10
ON = ENABLED
3 4 5 6 7 8 9 10