Table of Contents
Advertisement
Abnormal speed senso of the
Movement walking moto
That is ,no change of speed
42
code disk was detected in
excess of 6S
。
the position sensor is
abnormal of Core kneading
moto
That is, no change of
44
,
position code disk is detected
over 10S.
Abnormal speed senso of
Core kneading moto
，
46
more than 6S did not detect
the speed code disk change.
The position code of the
telescopic airbag of the
49
machine unit is abnormal
The position of the Core
kneading moto is Narrow
54
anomaly in wide position
The count sensor is abnormal
59
of the Backrest push rod.
The count sensor is abnormal
63
of the Calves push rod
When calves stretch out and
draw back, the count sensor
68
is abnormal.
The motor is broken
1.
，
or blocked
Drive circuit device
2.
damage
The position sensor
1.
is broken
The motor is broken
2.
or blocked
Drive circuit device
3.
damage
The motor is broken
1.
That is,
or blocked
Drive circuit device
2.
damage
The position sensor
1.
is broken
。
The position sensor
1.
is broken
The motor is broken
2.
or blocked
Drive circuit device
3.
damage
Count sensor bad
1.
Connection
2.
anomaly
The motor is broken
3.
or blocked
Drive circuit device
4.
damage
Count sensor bad
1.
Connection
2.
anomaly
The motor is broken
3.
or blocked
Drive circuit device
4.
damage
Count sensor bad
1.
Connection
2.
anomaly
The motor is broken
3.
or blocked
Drive circuit device
4.
damage
Check the connection between
1.
the motor and the movement
board
Check or replace moto
2.
Replacement of movement
3.
board
Check the connection between
1.
the sensor and the movement
board
Replacement of sensors
2.
Check or replace moto
3.
Replacement of movemetn
4.
board
Check the connection between
1.
the motor and the movement
board
Check or replace moto
2.
Replacement of movement
3.
board
Check the connection between
1.
the sensor and the movement
board
Replacement of sensors
2.
Replacement of movement
3.
board
Check the connection between
1.
the sensor and the movement
board
Replace the senso
2.
Check or replace moto
3.
Replace the movement board
4.
Check the connection
1.
Check or replace the push rod
2.
Replace the center board
3.
Check the connection
1.
Check or replace the push rod
2.
Replace the center board
3.
Check the connection
1.
Check or replace the push rod
2.
Replace the center board
3.
Detection when
(1)
function is turned on
Shut down
(2)
automatically in the
event of failure time.
And not allowed to boot.
Detection when
(1)
function is turned on
Shut down
(2)
automatically in the
event of failure time.
And not allowed to boot.
Detection when
(1)
function is turned on
Shut down
(2)
automatically in the
event of failure time.
And not allowed to boo
。
) Detection when
(1
function is turned on
Shut down
(2)
automatically in the
event of failure time.
And not allowed to boot.
Detection when
(1)
function is turned on
Shut down
(2)
automatically in the
event of failure time.
And not allowed to boot.
Detection when
(1)
function is turned on
Shut down
(2)
automatically in the
event of failure time.
And not allowed to boot.
Detection when
(1)
function is turned on
Shut down
(2)
automatically in the
event of failure time.
And not allowed to boot
Detection when
(1)
function is turned on
Shut down
(2)
automatically in the
event of failure time.
And not allowed to boot
Advertisement
Table of Contents
