EnGenius DuraFon 1X Quick Reference Sheet page 2

NOTE: if you use all 9 ID's (up to 19), you will get a "Register Failed" prompt. You must reset the Base Station and
start over if no more ID's are available.
Ref #7 – Deregistering a Handset:
First power-up the Base Station for at least 5 seconds. PRESS and HOLD the register button (REG) on the base,
until all four green LED lights illuminate. Then on the handset PRESS MENU, 6 (register), then 2 (deregister). The
Handset will display "Deregister" The ID of the Handset is now removed from the Base Station and the Handset. If
the Handset won't deregister, then it probably wasn't registered to the Base Station in the first place, or lost its
configuration, follow steps #5 and #6 above.
Ref #8 – Using more than one Base Station (linked):
The DuraFon 1X system allows you to add additional Base Stations, and therefore more than one line. To add
additional Base Station units, please first register all Handsets to the primary base originally used in the system.
Now get an administrator Handset (ID 11, or 12) and the additional Base Station unit you plan to add. First power-up
that Base Station for at least 15 seconds. Now PRESS and HOLD down the REG (register) button on the Base
Station until all four green LED lights illuminate. Next, PRESS MENU on the Handset, 6 (register) 3 (add base), and
then choose 20 (for Base #2). Note additional Base Stations 3, and 4 can be done the same way, however, their
Base Station numbers would be 30, and 40 accordingly.
Ref #9 – Internal Audio Adjustments
(To check firmware version PRESS MENU, Star(*), Star(*), Pound(#), then 1 (base ID is default 10 or 20,30,or 40 in
multiple base cross registered applications).
HANDSET EARPIECE OUTPUT ADJUSTMENT
NOTE First confirm you already set volume to "6" while on an active call but still need volume to be louder.
1) PRESS MENU, Star(*), Star(*), Pound(#), then press Option "2" for "Boardtest"
2) PRESS 41 and you will be in the "Codec Out" test. You should hear a 1 kHz tone.
3) For v1 (firmware version 0.xx through 1.xx) note the digit on the bottom right corner. Default is typically
between 3 and 5. Zero is loudest, 9 is lowest, adjust accordingly.
4) For v2 (firmware 3.xx) adjust 1 through 6, where 1 is lowest, 6 is loudest.
5) After changing the value press "End" to finish and again to exit.
HANDSET MICROPHONE SENSITIVITY ADJUSTMENT
1) PRESS MENU, Star(*), Star(*), Pound(#) then press Option "2" for "Boardtest"
2) PRESS 51 and you will be in the "Codec In" test.
3) For v1 (firmware version 0.xx through 1.xx) note the digit on the bottom right corner. Default is typically
between 3 and 5. Zero is loudest, 9 is lowest. Adjust accordingly.
4) For v2 (firmware version 3.xx) PRESS the top left soft key (OPTION), then use the arrow up/down key to
adjust. Typical default is 30.75db. Adjust up or down in 3db increments at a time, then test. PRESS the top
left soft key to "SAVE".
5) After changing the value PRESS "End" to finish and again to exit.
6) If the audio out-going is still not loud enough, try adjusting base line out levels (below).
Still having trouble? Call EnGenius technical support at 888-735-7888 x 514 or email
For further support please email
support@engeniustech.com
DuraFon 1X FAQs
Revised 1/12/2012