Use - ROSIERES FE GD21 RB User Instructions

THE CHOICE OF COOKWARE - The following information will help
you to choose cookware which will give good performance.
Stainless Steel : highly recommended. Especially good with a
sandwich clad base. The sandwich base combines the benefits of
stainless steel (appearance, durability and stability) with the
advantages of aluminium or copper (heat conduction, even heat
distribution).
Aluminium : heavy weight recommended. Good conductivity.
Aluminium residues sometimes appear as scratches on the hob, but
can be removed if cleaned immediately.
Because of its low melting point, thin aluminium should not be used.
Cast Iron : usable, but not recommended. Poor performance. May
scratch the surface.
Copper Bottom / stoneware: heavy weight recommended. Good
performance, but copper may leave residues which can appear as
scratches. The residues can be removed, as long as the hob is
cleaned immediately. However, do not let these pots boil
dry. Overheated metal can bond to glass hobs. An overheated copper
pot will leave a residue that will permanently stain the hob.
Porcelain/enamel : Good perfomance only with a thiny smooth, flat
base.
Glass-ceramic : not recommended. Poor performance. May scratch
the surface.

6. USE

How to choose power management level
Through the "Power management" function, the user can set the
maximum power that can be reached by the hob. Power management
function is only available during first 30 seconds after switch on the
hob. There is even the possibility to repeat this setting switching off
and on the power plug. By setting the desired maximum power, the
hob automatically adjusts the distribution in the various cooking zones
so that this limit is never exceeded; with the added advantage of being
able to simultaneously manage all the zones without overload
problems. The customer can set the maximum power of hob between
2.5 kW and the maximum related power of the hob (this can change
according to the model). For example if the maximum power of the hob
is 7 kW, the maximum power level for setting is between 2.5kW and
7 kW. After connecting the appliance to the electrical power, within 30
seconds you can set the power level based on the points shown
below:
1.- Sw tch on hob.
2.- Let touch control f n sh ts n t al zat on process.
3.-Unlock the control.
8
P
8
4.- Before pass 30 seconds after switch on the hob; touch for 5
seconds "-" key of timer.
8
8 8
8
5.- After this moment, this message will appear on display, Po on timer
display. Power level divided by 100 in heater displays.
0
P
6
8
8
8
8
0
5
07 GB
6.- Using '+' and '-' of Timer keys, Power Management value can be
adjusted. When requ red value s selected, touch at the same t me "+"
and "–" keys dur ng 5 seconds.
0
P
4
7.- When th s process s f n shed, a long beep s heard and a reset s
produced. Start-up process w ll be generated aga n.
8
8 8
8
8.- After start-up process, in timer display power management will be
showed.
0
P
4
After that, touch control won´t allow any comb nat on wh ch
can exceed th s l m t.
Notes:
a) Th s power management s only ava lable dur ng f rst 30 seconds
after sw tch on the hob.
b) If th s power management select on s ON, f more than 90 seconds
after sw tch on the hob th s process w ll be f n sh w thout
any new power value were recorded.
c) If th s power management select on s ON, f any key s touched
except the comb nat on of t mer "+" and "–", process
w ll be f n sh w thout any new power value were recorded and touch
control w ll start work ng as usual, w thout reset.
d) If th s power management select on s ON, f any key s touched the
comb nat on of t mer "+" and "–", process w ll be
f n sh w th a new power value were recorded , reset and touch
control w ll start work ng as usual.
Switch ON/OFF a heater zone
8
8 8
8
To switch ON a heater Touch power key during 400 msec. Long beep
will be heard and "0" value will appear in target zone digit, indicating
power level.
1) If any cooking stage is in position 0, this display will switch OFF
automatically after 10 seconds and the zone OFF sequence will
sound.
2) If there is residual heat indication in the display which is ON but in 0
power, "0" will appear changing over.
3) If lock function is active you cannot switch ON a zone.
To switch OFF a heater Touch power key during 1,2 sec. 3 Short
beeps will be heard and nothing or "H" value will appear in target zone
digit if residual heat exists. Zone will be OFF.
1) If any cooking stage is in position 0, this display will switch OFF
automatically after 10 seconds and the zone OFF sequence will
sound.
2) If there is residual heat indication in the display which is OFF, "H"
will be displayed.
3) Even lock function is active you can switch OFF a zone.
4) If only one heater is active and this one is switched off, 4 Short beep
will be heard indicating all cook top is Off.
0
5
8
8
0
5
8
8