Page 1
___________________________________________________________________________________________ DIAMOND VIEW _________________________________________________________________ Service Manual for Diamond View TFT Monitors: DV155 & DV155B ___________________________________________________ ___________________________ The release of this document is under control of the company. Extra copies of this document must be by written permission of the product manager.
Products powered by electricity should be serviced or repaired only by experienced professional technicians. Any attempt to service or repair the product or products dealt within this service information by anyone else could result in serious injury or death. _____________________________________________________________________________________________________________________________ DV155 & DV155B service manual Page: 3 of 44...
1 milliamp. In the case of a measurement exceeding the 1 milliamp value, a rework is required to eliminate the chance of a shock hazard. AC VOLTMETER 0.15u 1500 Earth Ground To Metal Parts _____________________________________________________________________________________________________________________________ DV155 & DV155B service manual Page: 4 of 44...
2.2.8 Superior display performance High contrast: 400: 1(Typical) High brightness: 250 cd / m2 (Typical) Wide view angle: 120 / 90 degrees (H/V) 2.2.9 Special function VESA DDC2B (Display Data Channel) Compatible _____________________________________________________________________________________________________________________________ DV155 & DV155B service manual Page: 7 of 44...
0.297 mm Response time Typical 25 ms View angle (L/R/T/B) 60/60/55/45 degrees Color coordinate white x=0.312,y=0.318 3.4. CONNECTORS 3.4.1 AC inlet: CEE22 typed connector 3.4.2 Audio: Line-in receptacle PHONEJACK STEREO _____________________________________________________________________________________________________________________________ DV155 & DV155B service manual Page: 8 of 44...
Page 9
< 1 Watts < 30 seconds Remark: In case of “no signal“ Power LED must be amber. At first power on w/o signal LED will be green + message on screen. _____________________________________________________________________________________________________________________________ DV155 & DV155B service manual Page: 9 of 44...
Page 10
+ / + - /- + / + + / + Note: *Indicates horizontal front / back porch includes borders # Indicates vertical front / back porch includes borders 3.5.6 General performance _____________________________________________________________________________________________________________________________ DV155 & DV155B service manual Page: 10 of 44...
Page 11
-20°C - +60° C Humidity: 10% - 85% Height: 3000 m Air pressure: 700 - 1060 mbar Transport (packed) Temperature: -30°C - +60° C Humidity: 5% - 95% Height: 12000 m _____________________________________________________________________________________________________________________________ DV155 & DV155B service manual Page: 11 of 44...
Page 12
Signal cable with Mini D-Sub 15P connectors, Length: 1.8 meter. 3.11. RELIABILITY MTBF > 30000hrs (demonstrated MTBF) For LCD panel: The brightness is still more than 50% of the original brightness after: typ. 20.000 hours _____________________________________________________________________________________________________________________________ DV155 & DV155B service manual Page: 12 of 44...
Panel interface (Pin 66~137) The MST8016 driver interface is highly programmable. It supports dual bus / dual port for XGA drivers. _____________________________________________________________________________________________________________________________ DV155 & DV155B service manual Page: 13 of 44...
Page 14
P6.0 (KEY in) Control button input P3.1 (VGA SDA) EDID data connect to VGA port P3.5 (VGA SCL) EDID clock connect to VGA port P1.4 (Reset) Provide Reset signal for MST8016 _____________________________________________________________________________________________________________________________ DV155 & DV155B service manual Page: 14 of 44...
Page 15
TDA7496 can directly drive 8 ohms speaker, does not require output coupling capacitor, bootstrap capacitor, or snubber network. Audio line-in are fed into pin 4,8 of the AN7522. The output power is controlled by the DC voltage of pin 39 from MTV312 I / O port. _____________________________________________________________________________________________________________________________ DV155 & DV155B service manual Page: 15 of 44...
1) remove four large screw "1" from the rear cover 2) remove the back cover 2. Bezel removal 1) remove screw "1" & “2” from the Bezel 2) remove the bezel _____________________________________________________________________________________________________________________________ DV155 & DV155B service manual Page: 16 of 44...
Page 17
4) remove cable 4 & 5 then remove Power/Inv board 4. AD board removal 1) remove cables 1, 4 & 5 2) remove screw “2” & “3” 3) remove the AD board _____________________________________________________________________________________________________________________________ DV155 & DV155B service manual Page: 17 of 44...
2. Perform Auto configuration. POWER POWER Switch Power ON/OFF LED Status Color Status Description Green Normal status Enter Sleep Mode status or use “Power + Auto” key enter Amber factory mode _____________________________________________________________________________________________________________________________ DV155 & DV155B service manual Page: 18 of 44...
Page 19
This menu will display about 45 seconds. Auto Configuration When user press the select/Auto key under none OSD status will trigger this dialog appear and perform Auto Configuration procedure. _____________________________________________________________________________________________________________________________ DV155 & DV155B service manual Page: 19 of 44...
Page 20
5 seconds for testing the power consumer. Out Of Range When user input the video signal out of spec this dialog will appear about 20 seconds. And then enter the Sleep mode. _____________________________________________________________________________________________________________________________ DV155 & DV155B service manual Page: 20 of 44...
Page 21
Adjust the horizontal position of the picture. Color Adjustment There are four items for color adjustment: 9300K: Bluish white 6500K: Reddish white User defined: Red, Green, Blue. Adjust to set your own color level. _____________________________________________________________________________________________________________________________ DV155 & DV155B service manual Page: 21 of 44...
Page 22
VERSION: Display F/W version and panel vender and DDC serial no. /A: LG panel /B: CPT panel /C: Hanstar panel /D: Sharp panel _____________________________________________________________________________________________________________________________ DV155 & DV155B service manual Page: 22 of 44...
3 Video Generator: Chroma 2000, 2135,2250 or equivalent like test program (Display Mate) 4 Color Analyzer: Minolta CA110, Chroma or equivalent 5 Watt / Power Meter 6 10 Times Magnifier 7 Multimeter 8 Oscilloscope _____________________________________________________________________________________________________________________________ DV155 & DV155B service manual Page: 23 of 44...
8. BLOCK DIAGRAM L5TD Block Diagram Main Board LCD Monitor Button & LED Board CPU(with Flash ROM) Myson MTV312 DDC signal PC VGA port R, G, B x 6 bits x dual pixel = 36bits Panel power, clock, Hs, Vs, DEN TFT LCD MSTAR MST8016...
Page 34
Diamond View DV155 & DV155B _____________________________________________________________________________________________________________________ Button Board POWER ON/OFF POWER ON/OFF HDK632R-ST TO BOARD CN10 POWER ON/OFF KEY 1 LEDG LEDR R100 HDK632R-ST 4606-05-05P-R 220/8 DOWN DOWN DOWN R101 HDK632R-ST 330/8 LEFT LEFT LEFT HDK632R-ST R102 560/8 RIGH RIGH...
Page 42
Diamond View DV155 & DV155B ________________________________________________________________________________________________________ 15. Auto White Balance Procedure Connect signal to monitor. The display signal need contain real black and full white. Press "Auto" button (don't release) when power ON (LED display Amber). Press OSD select FACTORY 2, Auto Color, RUN (For AD converter calibration on R, G and B gain, offset).
Need help?
Do you have a question about the DV155 and is the answer not in the manual?
Questions and answers