Related Manuals for EDS NEPTUNE EGX Series
Summary of Contents for EDS NEPTUNE EGX Series
- Page 1 NEPTUNE EGX Series EGMX / EGLX GAS DETECTION EXPLOSION - PROOF GAS DETECTORS User’s Manual & Warranty Certificate www.edselectronic.com...
-
Page 2: Liability Limitation
Liability Limitation To the extent allowed by the laws, EDS shall not be responsible, within the framework of any liability whatsoever, for any loss or business loss, usage loss, interruption of works, data loss, or any other indirect, incidental, special, or conditional damages that arise from contract, tort, negligence, product li- ability, or any other issue. - Page 3 DESCRIPTION The EGMX and EGLX explosion-proof gas detectors have been developed to continuously measure the flammable gas in the air. The EGMX model is designed to measure the amount of methane gas in the range of 0-60% LEL. The EGLX model is designed to measure the amount of LPG in the range of 0-60% LEL.
- Page 4 Addressable Nitrogen Oxide Detector EGOS Addressable External Siren EGLS Addressable Loop Siren Addressable Relay EGIM Addressable 4-20mA Input Module...
-
Page 5: Technical Drawing
TECHNICAL DRAWING... -
Page 6: Technical Specifications
TECHNICAL SPECIFICATIONS Model EGLX EGMX Environmental class Outdoor Electrical Nominal voltage 4-20mA/RS485(Optional) Supply voltage range 19 – 28V DC Stand-by current <32mA(24VDC) Yellow Fault LED indicator Green Operation Sensor Sensor type Catalytic Detection gases Methane Detection range 0-60% LEL Measurement unit Response time <10 s Sensor life... - Page 7 The first 2 digits of the serial number on the product indicate the production date (The number on the label of the product). Producer EDS Elektronik Destek Sanayi ve Ticaret Ltd. Meclis Mah. Teraziler Cad. Hayran Sk. No: 4 34785 Sancaktepe / İstanbul / Turkey...
-
Page 8: Mounting And Cabling
MOUNTING AND CABLING This section describes the detector mounting. Please do not start the mounting process without understanding the system, its parts and the working principle of the system. It is recommended to start the assembly after reading the warnings and points to be considered. - Page 9 Choose a clean and smooth wall at eye level. Be careful to install it in an area where there is no air flow, no fans and no vibration. It is not recommended to be installed close to radio frequency devices. Make sure that it is installed in a suitable area for calibration and maintenance.
- Page 10 Cabling Labels and cable functions should be stated in the cablings made. A proper cabling should be supplied for electrical terminals. You can reeve the cables from the holes in the lower box for 4-20mA cabling and Relay cabling. 8 connections can be made to control panel directly to the control panel. If more connection is required 4-20mA input module must be used.
-
Page 11: Electrical Connection
Wall Mounting Place 20M Cable Gland Connection Sensor Place Figure 3 : Gas Detector Illustration Electrical Connection Detector connections are as shown in Figure 3. Panel Connection Sensor Connection Power Error LED Figure 4 : Gas Detector Connection... - Page 12 Control Panel Detector Connections The connection between the detector and the control panel is made according to Figure 5. Figure 5 : Control Panel Detector Connections...
- Page 13 Detector to 4-20mA Input Module Connection Detectors can be connected to the control panel via 4-20mA input module from IN connections. INX to IOUT, 24V to +V and GND to GND connection must be made. For 4-20mA connection please refer to EGP control panel user manual. Figure 6 : Detector to 4-20mA Input Module Connection Scheme...
-
Page 14: First Operation
FIRST OPERATION Power up the detector. Make the necessary output connections. Plug the detector to the control panel. You can see your data after making detector cable connections to the control panel. In normal operation, the green LED lights. The yellow LED lights during error. -
Page 15: Troubleshooting
TROUBLESHOOTING Errors in the detector are shown at the control panel. In case of error, the yellow LED on the detector flashes continuously. If there is a communication error, the cable connections should be checked. Breaks in the cables may cause an error. WARNING Make sure to make the connections properly. - Page 16 When your device has reached the end of its useful life, contact your local authority for disposal and recycling options, take it to a collection point for the recycling of electrical and electronic equipment or hand it over to EDS Elektronik. This product does not contain harmful or prohibited substances specified in the Regulation on the Control of Waste Electrical and Electronic Equipment issued by the Turkish Republic Ministry of Environment and Urbanization.
-
Page 17: Warranty Certificate
WARRANTY CERTIFICATE The terms of the warranty is valid for products sold in Europe Union. Failure to occur during loading, unloading and shipment after delivery of the goods is not covered by the warranty. Damage, malfunction and information services caused by operating errors are not covered by the warranty. - Page 18 This period starts from the notification date of the product’s failure to the service station and in default of the service station, so one of those as the product’s seller, dealer, agent, representation,importer or importer-produ- cer. If the product is not troubleshot with in 10 days, the importer-producer or importer must assign another product within similar properties to the use of the consumer till the product’s repair is completed.
- Page 19 Ministry of Customs and Trade. Producer Manufacturer title / Service address: Stamp / Signature: EDS Elektronik Destek San. ve Tic. Ltd. Şti. Meclis Mah. Teraziler Cad. Hayran Sok. No:4 34785 Sancaktepe/Istanbul/Turkey Tel: 0216 528 45 00 Fax: 0216 314 17 80 e-mail: eds@eds.com.tr www.edselectronic.com...
- Page 20 EGMX-EGLX-UM-2238-R0 EDS Elektronik Destek San.ve Tic. Ltd. Şti. Meclis Mah. Teraziler Cad. Hayran sk. No:4 34785 Sancaktepe /İstanbul /Turkey +90 216 528 45 00 eds@eds.com.tr www.eds.com.tr...
Need help?
Do you have a question about the NEPTUNE EGX Series and is the answer not in the manual?
Questions and answers