Table of Contents
Advertisement
Quick Links
R
Powerhouse XL
Operating Instructions
Rytec website:
Rytec E‐mail: helpdesk@rytecdoors.com, Parts E‐mail: parts@rytecdoors.com
Y
Jazz PLC
Dual Drive Door
P.O. Box 403, One Cedar Parkway, Jackson, WI 53037
Phone 262‐677‐9046 Fax 262‐677‐2058
www.rytecdoors.com
[Revision: December 10, 2012 R1600614‐0, ©Rytec Corporation 2012]
T
Rytec On-line store: www.rytecparts.com,
E
®
C
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for RYTEC Powerhouse XL Jazz PLC
Summary of Contents for RYTEC Powerhouse XL Jazz PLC
- Page 1 Operating Instructions P.O. Box 403, One Cedar Parkway, Jackson, WI 53037 Phone 262‐677‐9046 Fax 262‐677‐2058 Rytec website: www.rytecdoors.com Rytec On-line store: www.rytecparts.com, Rytec E‐mail: helpdesk@rytecdoors.com, Parts E‐mail: parts@rytecdoors.com [Revision: December 10, 2012 R1600614‐0, ©Rytec Corporation 2012]...
-
Page 3: Table Of Contents
TABLE OF CONTENTS PAGE INTRODUCTION..........1 HOW TO USE MANUAL . -
Page 5: Introduction
GENERAL OVERVIEW The PLC uses input signals from the limit switches to The Rytec Corporation is using the Unitronics Jazz PLC indicate to the controller what position the door is in. to control the dual motors of the Powerhouse XL door. -
Page 6: Connecting I/O's
PROGRAMMING OR ACCESSING THE PLC—ENTERING THE PROGRAMMING The bottom connector generally provides analog and/or 4. The display will read for 2 seconds: digital output connection points. Connecting I/O’s ACCESS: GRANTED 1. Strip the wire to a length of 7mm (.250—.300 in.). 2. -
Page 7: Setting Timers
Home display input or output, actual programming for the input or output performed under Menu: Door function (Inputs) or Menu: Output relay. See later in this manual. SETTING TIMERS Rytec 0000111 Closed Down Arrow A5900001 Figure 5 6. Push the down arrow. - Page 8 PROGRAMMING OR ACCESSING THE PLC—SETTING TIMERS 5. The display will now read: T1 Open Run T X Seconds (0-60) Menu: Home display A5900001 Figure 4 Down Arrow A5900001 6. Press the down arrow until you reach. Figure 7 IMPORTANT: The open run timer is a backup Menu: Timers timer for the opening, timer...
-
Page 9: Door Function
PROGRAMMING OR ACCESSING THE PLC—DOOR FUNCTION DOOR FUNCTION T3 Auto Close T Set the function of inputs 13 (open) and 14 (close) XX seconds (0-60) option to run door with timer or without. Rytec 0000112 Closed A5900001 Figure 10 A5900001... -
Page 10: Output Relay
OUTPUT RELAY Powerhouse XL control has a CR1 relay available to A5900001 monitor door or warning device, e.g. horn and lights. Figure 4 6. Press the down arrow until you reach. Rytec 0000113 Closed Menu: Output Relay A5900001 Figure 1 1. -
Page 11: Alarm Conditions
ALARM CONDITIONS—OUTPUT RELAY 8. The display will read: Output Relay 4: Door Opening Output Relay: X X: “Door”xxxx” A5900001 Figure 10 Output Relay 4 Down Arrow 5: Door Closing A5900001 Figure 6 IMPORTANT: The relay (CR1) has 5 options available as to when CR1 will be active: X represents the number A5900001 of the function 0-5 (skips 3) and... -
Page 12: Safety Limits
The drive motor has red and green handles hanging from the bottom of the motor. When the green handle is pulled or in the lowest position, the drive motor is Rytec 0000114 engaged to run on electrical power. When the red han-... -
Page 13: Chain Proximity Sensor
ALARM CONDITIONS—CHAIN PROXIMITY SENSOR CHAIN PROXIMITY SENSOR Rytec 0000117 The chain proximity sensors are part of an emergency Load Sensor RH stop circuit. If a chain breaks the proximity sensor opens the emergency stop circuit and the controller stops the door. -
Page 14: Wireless Reversing Edge
• Check proper door communications are working. • Check battery in the bottom bar. • Press the yellow button to reset the controller. If there are any questions, please call the Rytec Technical Support at 1-800-628-1909 with the door serial number. - Page 15 NOTES...
Need help?
Do you have a question about the Powerhouse XL Jazz PLC and is the answer not in the manual?
Questions and answers