Maintenance - Sealey MS925PS.V2 Manual

Contact your Sealey Stockist for details of compound heads and lambswool bonnets.

6. MAINTENANCE

.
WARNING! Before attempting any maintenance ensure the unit is unplugged from the mains power supply.
‰
6.1. Keep the machine clean and dry. Clean with a damp cloth;
DO NOT use abrasive or solvent cleaners.
8
6.2. Clean regularly by blowing a jet of compressed air through side vents to ensure motor ventilation is kept clear.
WARNING! Wear approved safety eye protection and, if necessary, respiratory protection.
‰
NOTE. The following maintenance must only be carried out by a technically qualified person or an authorised Sealey service agent.
6.3. Check carbon brushes by removing each side brush holder (fig.2).
6.4. Check to see if the brushes are worn or cracked (fig.3). If so, the brushes must be replaced to avoid sparking and damage to the
armature. Always change brushes as a pair. Use only genuine spare parts as these are specifically designed for the machine.
Failure to do so may be dangerous and will invalidate your warranty.
6.5.
After each 500 hours of use replace the gear head grease to prevent gear wear and possible drive failure.
‰ WARNING! – Risk of Hand Arm Vibration Injury.
This tool may cause Hand Arm Vibration Syndrome if its use is not managed adequately.
This tool is subject to the vibration testing section of the Machinery Directive 2006/42/EC.
This tool is to be operated in accordance with these instructions.
Measured vibration emission value (a): 11.83 m/s²
Uncertainty value (k):1.5 m/s²
Please note that the application of the tool to a sole specialist task may produce a different average
vibration emission. We recommend that a
specific evaluation of the vibration emission is conducted prior to commencing with a specialist task.
A health and safety assessment by the user (or employer) will need to be carried out to determine the
suitable duration of use for each tool.
NB: Stated Vibration Emission values are type-test values and are intended to be typical.
Whilst in use, the actual value will vary considerably from and depend on many factors.
Such factors include; the operator, the task and the inserted tool or consumable.
NB: ensure that the length of leader hoses is sufficient to allow unrestricted use, as this also helps to reduce vibration.
The state of maintenance of the tool itself is also an important factor, a poorly maintained tool will also increase the risk of Hand Arm Vibration
Syndrome.
Health surveillance.
We recommend a programme of health surveillance to detect early symptoms of vibration injury so that management procedures can be modified
accordingly.
Personal protective equipment.
We are not aware of any personal protective equipment (PPE) that provides protection against vibration injury that may result from the
uncontrolled use of this tool. We recommend a sufficient supply of clothing (including gloves) to enable the operator to remain warm and dry and
maintain good blood circulation in fingers etc. Please note that the most effective protection is prevention, please refer to the Correct Use and
Maintenance section in these instructions. Guidance relating to the management of hand arm vibration can be found on the HSC website
www.hse.gov.uk - Hand-Arm Vibration at Work.
WEEE REGULATIONS
Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic Equipment
(WEEE). When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid
waste authority for recycling information.
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice. Please note that other versions of this product are available. If you require documentation for alternative versions, please email or call our
technical team on technical@sealey.co.uk or 01284 757505.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500
© Jack Sealey Limited
01284 703534 sales@sealey.co.uk
Original Language Version
fig.3
www.sealey.co.uk
MS925PS.V2 Issue 3 (3) 01/04/22